Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Hi,i want to configure my cisco 1242ag series ap(autonomous) to work as internet gateway.how can i connect it to network so that it will work as internet gateway for users.
Hi All,I would like to replace a AIR-WLC4402-25-K9 with AIR-WLC4402-50-K9 because of the AP amount issue. Both controllers are running on the same software version 4.2.61.0 . Just out of curiosity, can I just backup the configuration from the old one...
Hi all,I need you help on the issue which i am facin.I have guest users wireless access and when I connect to the access point,It does prompt me for the username and passowrd I enter and then it tries to connect to internet and then does nothing.Is t...
We killed an aironet 1242AG access point - someone installed the LWAPP software and it either got corrupted or the software itself changes the way the device functions dramatically. In anycase we want to revert it back to the way it is supposed to b...
Hello,Firstly, i'm sorry if this answer is already answered.I have a network with :1242 AP's (autonomous/lighteweight) 4400 WLC.and i would like to make this design :Wireless client <-----> 1242 AP's running autonomous <-----------------------> 1242...
Trying to download latest WLC and recieve the following error:Authorization Failed. No sufficient privilegesUser account I am using has read/write access.Any thoughts?Thanksizzy
I am running v6.0.196 on 2 WLCs. Aggressive Load Balancing is disabled globally via WCS. (Configure / Controller / General / Aggressive Load Balancing = Disabled). When running the Voice Audit Tool against the VoWLAN, I receive the following:"Aggre...
Hi all,I manage a WLC 4404 ( with 4.2.176.51M IoS) and I've only got 2 models of access points in the solution:For indoor - AIR-LAP1242AG-E-K9 For outdoor - LAP1510My question is if I can integrate any LAP iwith this WLC (mesh), like:...
Dear all,I've got an issue here with some 1242AG access points:A stationary mounted AP is configured to have two SSIDs in two VLANs on 2.4GHz radio module. One SSID is secured (WPA2), one not.A mobile AP is configured as a WGB and connects some clien...
Hello!Dear all, I have some problems integrating WLC 4400 with AD using ldapThe the WLC LDAP Server and WLAN for Web Authentication are configured acoording tohttp://www.cisco.com/en/US/products/ps6366/products_configuration_example09186a0080a03e09.s...
I have created an unique guest account in WLC 4402 version 4.2 and distribute it to every visitor that comes into our company. However, when we receive many visitors, the WLC stops authenticating. Does anybody know if there is a limit in using a same...
We have Cisco lightwight AP (AIR-LAP1131AG-E-K9) and controller ( AIR-WLC4402-50-K9) installed and to support a new third party management system, we would like to downgrade these access points or upgrade the firmwares to work as a standalone Autono...
HelloI need to connect 2 buildings (800Meter) over a wireless bridge, the connection requires high bandwidth (300 Mbps).Now I would like to buy 2 AIR-AP1252AG-E-K9. At the moment I'm not sure which antenna I have to take. I thought about the AIR-ANT1...
Experts, i did some reading but find it difficult to get a clear view.i am looking to understand the differences between MAP, RAP & WGB in cisco wireless and what conditions these are used for.thanks in advance.
I have a wireless setup of WLC 4402 and four 1250 APs.There are about 10 users. Some times they have freezes and lags in network connection.The end users notice ping latency above 5ms, below is a ping test for 30 seconds.Reply from 10.1.10.160: byte...
