Wireless

wlc4402 5.0.148.0 Windows clients have very poor access to network resources inside of our network. The wlan is on a tagged interface associated to a port that is a vlan trunked port on our 6509. If a wlan that is associated to our non-tagged manag...

Hi,I have all of my WAP's connected and managed by my WLSE but it showing that they all have the same name under Devices > Group Management as well as when I try to deploy new templates. If I dig into device explorer it shows the "Full Name" as the w...

Hi Folks, i had to use the WCS Planner to make a quantity structure for a new Building. This Building has some Inner Courtyards, where WLAN coverage is undesired. How can i exclude these Areas from the Map in the Planner Tool? Any Idea? What is teh D...

i have a cisco air-1230b-a-k9 access point accidentally it was lost it's ios.while i tried to load ios through xmodem it is showing me that no space left in device. though there is no file system in flash

I have a customer that has asked if he can import an AP configuration into WLSE and create a deployable template from it for additional AP installations?

Just wondering if anyone has ever seen these logs on there controllers before and if so what do they mean?Oct 30 09:39:50.839 apf_foreignap.c:1278 APF-4-REGISTER_IPADD_ON_MSCB_FAILED: Could not Register IP Add on MSCB. MSCB still in init state. Addre...

Ive got a WLSE and a bunch of APs, Can I push out a command from the WLSE to update all the APs so that they are prepared to support DST this weekend? Or do I have to do this manually for every AP?

LAP,power-supply is AIR-PWRINJ3error message is output in wlc,how can i resolve this ???thanksLog System Time Trap 0 Wed Aug 13 23:40:58 2008 AP's Interface:1(802.11a) Operation State Down: Base Radio MAC:00:1f:26:2a:b1:f0 Cause=Radio Low Power 1 Wed...

Hi,I received an AP1131 from my custoemer who said it just quit working. I checked the configuration in CLI and Graphic Interface where I found a message in "interfaces" that showed Ethernet but radios 0 y 1 said not installed. I reload the version b...

Hi guys,i have a 2106 WLC with three 1131AP LWAPP.I should cover a zone where there is no network cabling and i was thinking about another 1131 in mesh mode.Do I need particular software release?Can anyone provide documentation from which i can start...

Hi guys,I have a 2106 with a non mesh release and four 1131.I need two oh these 1131 work as RAP and MAP so i i understood well the steps required are:1)Donwload a mesh release2)Once Ap are controlled change their operative modeDo I miss something?Th...

I am configuring some AIR-LAP1242AG AP's with a variety of external antennae. I notice within the WLC the antenna gain should be value which is then "x 0.5 dBm". My question is for an AIR-ANT4941 antenna, which is a 2.2 dBi Dipole 2.4 GHz, what sho...

Cisco have been kind enough to lend us a 4404 WLC and I've got to grips with setting up our WLANS on it and I can get an AP to pick up config from anywhere in our extended network.I am, however having a problem trying to get an access point to join t...

I have trouble capturing lwapp data frames. I have AP on port 1, i have instructed my switch (3750) to monitor this port and send it to a available port on the same switch (no stacking). On the second port , i connect my sniffer. I see lwapp control ...

I have network of 7 AP's all of them 1240 series running with full IOS. I have configured one AP as WDS and the same AP is configured as local Radius server for WDS. All the AP's get registered with WDS and clients also get connected but just after m...