Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

review


Labels

Forum Posts

Hi,I've a WLC2125 ( 2.2.193 ) that I often found with no traffic on ethernet port ( with no LAG ) .After that I've to reboot the WLC to fix the situation.The WLC is connected with just one port.Any idea ?Many thanks in advanceLuigi

WCS 4.2.81.0WLC 4.2.112.0Loc 3.1.36.0I have a very large map with currently 40 APs placed on it. Tt will have close to 80 when completed. Layer that are on:APAP HeatmapsClientsRogue APsResaved AP placement and recalc RF prediction. Antennas are all s...

twikel by • Community Member
  • 1406 Views
  • 3 replies
  • 0 Helpful votes

I am running 5 1252 AP's as "hotspots". I am using both the 5GHz and 2.4GHz radios. I am using a power injector to power the units. I am using 3 antennas on both radios and I'm using diversity mode. I can can see the A,B,and G signals, but no matter ...

HelloMy Configuration is:15 AP(1240AG 12.4(10b)JA ) 1x WLSE-1.1-HW (2.15.1u).One of the 15 AP is the local radius and the wds.Wds and radius works fine. All AP registered in wds.My Problem:After upgrade the wlse of version 2.15.1u the WLSE does not a...

KUMAident by • Community Member
  • 1946 Views
  • 5 replies
  • 0 Helpful votes

We are seeing what we perceive to be, less than optimal data throughput rates between the 1142 and the Intel 5300AGN.Configured as follows:WiSM w/ 6.0.182.0 code1142AGNWPA2-PSK AES802.11b radio OFF20MHz channelsWMM EnabledDell Latitude E5400INTEL 530...

Does anyone have Vocera and Spectralink successfully working within a LWAP environment running version 4.2.176.0. This will be my 1st deployment in implementing both vendors together. The Vocera badges are the largest of the two with only a handful o...

owensm by • Level 1
  • 42667 Views
  • 12 replies
  • 0 Helpful votes

My problem is that I Connected an AIR-PWRINJ3 power injector to a device that is not cisco however it has a port PoE 802.3af but the power injector is not working.What should I do to make the power injector work?

j.baez by • Level 3
  • 2251 Views
  • 2 replies
  • 0 Helpful votes

Hi,I'd like to know if some one has an installation with Wireless Controller release 6.0.182 and ip phone 7921 release 1.3(3). With these releases the ip phone randomly get the error "Leaving serviced area" not only while roaming but also when it is ...

Hi community,I used to work a lot with Cisco WLAN controllers. The last software I really tested was the last 4.2 release. But I still have a question regarding RRM, nobody was able to answer. Maybe some of you guys know it:I'm never completely sure ...

By referring to Voice over Wireless LAN 4.1 Design Guide RF design chapter, the recommended power level cell boundary for IP phone is -67 dBm => 43 feet client radius. And with 20% cell overlap, the distance between non-overlapped channel's AP is 59 ...

yokekhei1 by • Community Member
  • 2594 Views
  • 1 replies
  • 0 Helpful votes

I know larger Cisco Wireless LAN controllers have the ability to block Rogue APs. I have not seen this same feature in the 526. Is it possible to block APs that are not part of my wireless network.There are 3 Cisco 521 APs and a Cisco 526 controller....

damiangallo by • Community Member
  • 2561 Views
  • 5 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card