Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
I've got a WLAN that uses WPA2 with PEAP. My MS clients take advantage of Proactive Key Caching to roam from AP to AP without requiring a full 802.1x authentication each time. My Symbol mobile devices, even though they support WPA2, are doing a ful...
Hello - I have been asked to investigate changing our wireless network's authentication to 802.1x. Currently we are using WPA, TKIP with a pre-shared key. We have found that more folks are connecting via their cell phones\PDA's (we set them up with...
Hi experts! I have couple of questions for Wireless in a company that has 3 floors. My first question is, how can I measure the current backbone throughput of my current AP (Dlink DWL-2100AP)? There are about 10 wireless clients, 5 of these are Wir...
HI all,My wireless 526 controller is corrputed and now i am not able to load the image.any one can advise on how to reload the image ?i only see the below from consolethanksgrub> Possible commands are: blocklist boot bootp cat chainloader cmp color c...
Hi all,I posted another question about not being able to get my 1200 working with clients but I think I need to take a step back and take a closer look at my initial setup. I have this AP on a switchport but after thinking about this, I have vlans I ...
Resolved! "Object not found in device"
HiWhen I try to add new Controller in the WCS (ver. 4.1.91.0) I get this error:“Failed to add device to WCS Reason: Object not found in deviceâ€The Controller has been added earlier a then deleted again. When I try to re-add the controller again, ...
Hello.Due to "Excessive 802.11 Association Failures" and "Excessive 802.11 Authentication Failures", I have some users that cannot connect anymore to the WLC system.Is there a list of these "excluded" clients ??How can I remove one of these "excluded...
Hello,I am trying to create a WLAN with WPA2 and AES for our WVoIP through WCS. Every time I try to apply the template to the controllers I receive the following error: "WPA2 Security Not Supported in this controller version". WCS is version 5.0.89 a...
I have an AP keep generating this message AP 'Cisco_AP', interface '802.11b/g'. Interference threshold violated.How can i solve this?
I have a AIR-LAP1510AG outdoor access point that I am having a connection issue with. Someone cut the RJ45 end off that connects the AP to the power injector, so they could run the cable through a wall. Now I have to be the one to fix it.What is the ...
I would like to have internal users authenticate to Wireless LAN Controller Module using Windows IAS server. What option are there for me to present to users? Do they get a separate domain username/password box? Can it pass thru their existing dom...
Hello,One question that I haven't found an answer for yet!When the location appliance reaches the maximum number of tracking devices of 2500 what happens next???It stops collecting information for new devices?It deletes information for older devices ...
On one of our 1100 APs the wireless devices that are connected cannot ping or access each other. All devices are accessible from wired workstations, as well as from the AP itself. The affected devices can also access the other wireless devices when...
as titles suggests. I have multiple controllers with ap`s assigned to them. I also have WCS which can see these controllers and AP`s.on the controller I can set tx power levels from 1 - 7 .on the WCS I can also set 1 - 7 and the Dbm value is also sho...
can there be a different controller code on the anchor controller than the oter controllers in the group. It seems like I can not get guest users to work if the controller code on the anchor is different from the controller that the user is associat...
