Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Resolved! WLC 8510 HDD failure
We had one of our HDD fail and now the device won't boot at all. We can get into IMM and we are also able to use KVM to view the BIOS boot up and menu system. I've tried to boot off USB, CD ROM, and the other HDD but I cannot get this device to boo...
I cannot figure out why I cant find this setting...In the SSID overview there is a setting called"Wired clients are part of Wi-Fi network"This SSID is set to bridged mode.Heres the firewall settings:What am I missing?
Resolved! WLC CLI command to show clients
Hi everybodyI work with a Cisco 8540 WLC and I have to extract some connection statistics.Is there some command to list...- all clients connected to a specific SSID?- all clients connected to a specific APGroup?- all clients connected to a particular...
Hi,I need an advise from the experts. We are looking into replacing our Cisco 2504 Wireless Controller and were told that the C9800 model will be the best next available model. We currently have about 10 APs model AP AIR-CAP1602E-A-K9. My question is...
Resolved! Flexconnect on wlc 9800
Hi,We have a pair of 9800s in HA/SSO. About to migrate our APs from 8540 to 9800. As im recreating our SSIDs to the new 9800s, we cant get the one flexconnect SSID to work. The 4 centrally switched SSIDs work as expected. I have followed the various ...
Resolved! Access Point
Hi all, can the cisco catalyst AP model 9136I, act as Autonomous.
Does anyone have a Cisco 9800-L WLC Controller and successful installed a CA Signed Cert for Web Server? Not making the Certificate signing request, but actually already have the PEM and other files locally. Cisco TAC can't figure it out. The documen...
I am using a cable from Console to serial, and that cable connected from serial to usb and i am using PuTTY. I have tested this setup with a Catalyst 2960 switch and i got output, but when i am using the same configuration for the 2504 Wireless contr...
There are 4 AP' in the network, 2 AP's showing 802.1X failure, Remaining 2 AP's fine. All the AP's connected same switch.
Hi I have a set up a wireless network for one of our remote site where clients are meant to obtain an IP address from a DHCP server located at Head Office . However I m unable to connect to the SSID and getting the following error from the connection...
Hello,I am trying to set up a cisco 8500 series WLC and am running into issues accessing the web UI. Here is a cisco link with the ports listed:https://www.cisco.com/c/en/us/td/docs/wireless/controller/8500/install/guide/ctrl8500.pdfWe have an ethern...
Hello.We are in the process of moving a bunch of access points from an old supplier to us as a new supplier.The old supplier does have a WLC which "holds" all of the access points.I set up a new 9800 WLC, and tried to move one of the access points to...
There are consistent critical alerts on CISCO prime for only 5 of the APs stating "Authentication Request flood", and the error description is as follows: IDS 'Auth flood' Signature attack cleared on AP 'ABC' protocol '802.11a' on Controller 'x.x.x.5...
I got problem with my AP, here is the log please help me.BootROM - 1.78Booting from SPI flash, Secure modeBootROM: RSA Public key verification PASSEDBootROM: CSK block signature verification PASSEDBootROM: Boot header signature verification PASSEDBoo...
Hi. On my C9800-CL-universalk9.17.09.04a I often got alarms about high input error rate:- GigabitEthernet2 is up, line protocol is up- 198009883 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored- rx_errors 198009883- rx_q0_errors 198009883...
