Wireless

I am trying to upgrade the firmware on a Cisco 1200 AP via the web interface but keep getting an error saying not enough room on flash.The firware currently on the AP is c1200-k9w7-tar.123-8.JA2 and I am tring to upgrade to c1200-k9w7-tar.123-8.JEC2....

hi all,For customer solution, I tried use WLC 526 with 5.2.157.0 (in release notes, local eap mentioned as new funkcionality, but when I configured it by WLC release 5.0 configuration guide - it doesnt work.from sh wlan <ID> command i always see that...

I ran into this a few weeks back as I was trying to get some demo depot gear working for a POC. basically all of the 1131 AP's would not join the controller and I got these errorsMay 17 20:45:42.471: %LWAPP-3-RADIUS_ERR: spam_radius.c:108 Could not s...

We have two 4402 and 23 1242AG. 4402s use 5.2.157.0 image. All APs resets often.In the Trap Logs there are a messages that APs disassociated previously due to AP Reset. Last reboot reason: operator changed 11g mode.It happens on both controllers with...

I was wondering what features are available from a managing and support perspective with the 4400 series WCS. I was specifically curious as to whether the WCS is able to identify serial number of Cisco AP's associated to it.

I'm getting an the following error on my workgroup bridge. And I'm not able to pass traffic across it. *Mar 1 00:03:29.665: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up*Mar 1 00:05:48.860: %DOT11-4-UPLINK_DOWN: Int...

I have 2100 WLAN with cisco catalyst 3750 switch. I have two vlan on the switch which are 10.x.x.x and 192.168.x.x. The 10.xxx network are on wireless client nd the 192.168.x.x are on the wire client.I can only ping there default ip addr of each vlan...

I have a guest wireless network through my controllers and am using WCS to manage the controllers. The problem I am seeing is when users are prompted to log in to the guest network they can either use the guest user account the lobby ambassador has s...

Hi,I have a client that what to put surveillance cameras in railroad carriages (I think that's what is cold, in English).He what's to put two cameras per carriage.And, above wall, he what's to connect each camera directly, by wired, to one Access Poi...

Dear All,I have a big problem I have 4 wlc 4400 series with wcs and I have performance test with consultant and he request from me ti measure delay & jetter from any tool taking into your consideration I have VOIP over wirelessyou fast replay is high...

Hi All, i tried to configure a WGB (1252, 1242, both Autonomous) to work in an LWAPP Environment. I know the Configuration Examples and the Config Guide. I dont trust in WEP and TLS doesnt work instead the Customer has no PKI implemented so far. Can ...

can I have an IOS 857w router as root bridge and 1200 series in repeater mode ?I have non cisco wireless clients ? Doco says enabling aironet extensions for repeater mode means non cisco clients don't work well. Is this still the case ?Also i read so...

DearsI have these APs (AIR-AP1231G-A-K9) with 2.4 Ghz.I need Mesh Technology.Is it possible if i use modules of 5 GHz antennas and change IOS of APs from fat to lightweight and use controller.Can any one please confirm? or give some suggestion.Second...

Does anyone have Vocera and Spectralink working succesfully on the Same WLC version 4.2.176.0 This will be my 1st deployment in implementing both vendors together. The Vocera is largest of the two with only a handful of spectralink phones. One of my ...