Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Hello,I am trying to monitor an EWC but I can't get all information on my monitoring server through snmp.When I perform a snmpwalk I get few informations (look at the txt file attached to this post).But I want to be able to obtain more information li...
Hi,I am trying to grant the on site IT staff access to our Cisco 8540 WLC but only want them to have AP provisioning access, not full access. I can only see the users ReadOnly, ReadWrite or LobbyAdmin which doesn't fit my need.We do have an ISE serve...
I have a 2504 WLC series running 8.1.102.0 software version. Also I have 14 AIR-CAP1602E-A-K9 running the ap1g2-k9w8-mx.15.3.3-JBB software, and joined to the Cisco WLC in a production environment. Recently I bought 20 Air-Cap2702i-B-K9 running ap3g2...
Resolved! Cisco AP IOS update
hello I have a question during Cisco AP IOS Upgrade. I tried upgrading through GUI and I put C9800-AP-iosxe-wlc.bin in and I put ap1g7 in and booted it. And it does not boot and the log as below appears. ipv6 gw config loop in AC discovery CAPWAP ...
Resolved! Local Redundancy Port Type Mismatch
Hi folks. I have a pair of 9800-40s, 17.9.4 code. Having trouble making HA come up. I ran test wireless redundancy rping on both sides, and it fails. I am assuming they forgot to connect the RP ports, it is at a remote data center and they are going ...
Hi;Please consider the following error message captured from one of my 9130AXI APs:The following is the configuration applied on the controller:Any ideas?Thanks
Hi Fellow WLC users :i have a standby wlc as per below config : how can i test and confirm that HA is working fine and also need to pull the serial number of standby wlc - need help on this topic :(dpeeeevvdeee-eee) >show redundancy peer-system stati...
Hello Team,facing guest user authentication issuewlc model:9800-lios:17.9.4aAP-Mode-Flex connectGuest authentication: 802.1x/wpa+wpa2Issues is not with all the users and issue with few users.when user trying to connect initially the authentication t...
Hello,I'm planning to implement a wireless network in a site that has Azure AD.The wireless network will consists of a WLC and APs.So, how to integrate WLC with Azure AD in order to allow users authenticate through Azure and what is the best models t...
Hello Experts,In the L3/L7 ACL processing order, Does it match the 'Default permit any' rule in L3 ACL or just match the configured one?I have referred to the below document but could not see any L3 Rule which is no match but has an L7 match examples...
Hi All, Kindly help me with the instructor Led Course ECMS2 link so I can go through it.Thanks
Resolved! 802.1X(AD) + MAC Filtering via ISE
I currently am only doing 802.1X(AD) on the SSID. My users have figured out they can get their personal iPhone on the SSID by entering their AD credentials. I would like to do 802.1X(AD) + MAC Filtering via ISE. This way the device would have to be i...
Hey Guys, i've ran into some strange issue where i was able to migrate all 2800 series APs from old AirOS WLC (5508 8.4.100) to 9800-L version 17.9.4a However now when i tried to move the 2700 and 3700 series, they are not able to join the WLC and i ...
C9800L is connected to the Core Switch 9500, and the AP is connected in VLAN 100. A VLAN 100 SVI has been created in the Core Switch and an IP helper has been configured. IP addresses are successfully being released in VLAN 100 without any issues. Th...
