Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
I have recently started seeing an issue on my network and I need a better way to handle it. I have about 15 Aironet 1200 AP's and I do not have a central controller, they are all individual and running the newest IOS. Is there a way I can see very ea...
Has anyone setup a WLC 4402 and few 1130AP's on their network? Here's the scenario we have VLAN's setup on our network. We want to be able an employee can connect to the internal network and public connect to a DSL Internet. I got the internal employ...
Are there any documents on how the WLC handles Radio Resource Managment ( RRM )? Do you need dedicated APs to monitor the frequencies in use, are there any physical placement requirements?Also, can different antenna be used other than omni-directiona...
My company recently went from an old airspace 4024 with firmware 3-2-195-13 to a new 4402-50 running 4-1-185-0. Using Option 43 in DHCP allowed the new 4402 to see the AP's on different VLan's and Subnet's and issue IP addresses to the AP's and clien...
Does anyone know where I can find out the diameter of the 150ft ultra low loss cable that Cisco uses to connect external antennas to access points?thanksBruno Wollmann
Hi,it seems the lobby page is displaying only 20 guest users maximum.When we delete some, we can then see the rest of users.No possibility to browse several pages ?Is this a bug or a simple lack of feature?Thanks for help.
I have a Aironet 1231 with IOS 12.3(8)JEB1. I have enabled SNTP, but it still shows the time and date that are configured manually. How do you disable the manual time setting?
I just installed some new APs but my WLSE keeps sending error messages like this:Inconsistent device state found: Device "AP12": ifIndex=2, MAC=00-1c-f6-64-dc-50: "CISCO-DOT11-IF-MIB cd11IfStationConfigTable.cd11IfStationRole must be in the range [1....
Hello at all.I'm looking for a command to complete the accounting information on my CiscoSecure ACS server.How can I insert the Name (the client name) to the radius attributes that access-point sends to my radius?Thanks,Andrea.ap#sh dot asso802.11 Cl...
What is the difference in WAPs and lightweight WAPs? I installed the 1100 (I believe 1121's) series about two years ago (relatively small deployments <15 WAPs per site) and I dont recall hearing about lightweights then. I am getting back into the fie...
I need to specify a firewall capable of 100Mbps throughput and that support QoSIve been advised the following products- but they are vast price diffrences -- can i ask which would be the best solution and why the PIX515E-UR-BUN , but then I looked a ...
Hi,Just wondering what people do in their organisations to allow PDA's on their wireless Network.We currently have out laptops using WPA with PEAP.I wanted to do that same with PDA's but I have the problem with Self Signed Certs on our ACS (Will be t...
Hi there,I have a problem with a WLC.Wired PCs whthin a network belongs to one of the dynamic interfaces in WLC can not access WLC. The PC can not ping to WLC Mgmt. interface, also.I don't understand why the PC can not access WLC through ethernet.I k...
HiyaCurrently we are installing Aironet 1131s. The DHCP server provides IP addresses after MAC authentication.The root aironet units work fine. A wireless device can connect and will receive an IP address. However when we add an aironet repeater, dev...
Hi,I want to reserve a bandwidth of 64k for a special vlan. Is this possible on this device ?
