Hi,I have:Check Point 1470 Appliance - on this router and It is 1 Vlan with dhcp--> Switch Cisco SG250-50Pnext --> CISCO WLC 1815In Cisco WLC 1815 is Vlan corp and I want to create a new network, separated for guests only with Internet access, secure...
Forum Posts
hello,,,I have AP2802e-h-k9I try to download OS via tftp but I can not it.I try logging to rommon but I can not also what method to download OS to AP ?
We have an experience with high channel utilization as captured below and we experiencing slow connection with high latency.we have already activate CLIENT BALANCING in purpose to reduce these high channel utilization, but high channel utilization st...
I am working on the design of a point-to-point mesh link with two 9124 APs over a distance of 375 meter (enough ground clearance and free line of sight) with the requirement of 800 - 1000Mbit throughput, so roughly a factor 1.7 till 2 of wireless con...
Hi,Can you explain to me why a Cisco AP AIR-AP2802I-E-K9 doesn't send WLAN capability through LLDP TLV type 7 ? Just "bridge" capability is actually sent.Thanks in advance.Regards.
In case you missed it, a few new docs dropped which look pretty good for those new to enterprise wirelessMeraki Wireless for Enterprise - Security - Cisco Meraki DocumentationMeraki Wireless for Enterprise Best Practices- RF Design - Cisco Meraki Doc...
Resolved! WLC 5520 with only CIMC
Hi guys! I have bought a refurbished WLC 5520 and I noticed that it has not installed the iOS. Is it possible? At first configuration I connected my laptop to the Service Port and I gave it an IP but i can see just the CIMC page. How can I solve this...
Has anyone faced this issue?The upgrade was a 9800-cl on esxi Version 17.3.7 to 17.9.4aThe entire configuration is intact, and the wlc is operating as usual. But, we cannot access the web gui management dashboard. No matter what we get the day zero l...
Resolved! Catalyst 9800 GUI TACACS+ Command Set
Hi everybody;Based on practical studies, Catalyst 9800 WLCs support command authorization for GUI access. Unfortunately, I am currently unable to set up the application of a defined Command Set in ISE for a user in GUI mode. Here is my configuration:...
Hi,I am planning a new core cutover for a HA pair of campus 9800-40s using the RMI+RP redundancy model.The connections to new cores will increase the number of active trunk ports on each 9800 from 2 to 4.To add those members, I will have to shut the ...
Resolved! CBW 240AC - stuck in pending
I purchased a fourth CBW 240AC and added it to my network - and it's stuck in Pending.After DHCP succeeds (blinking red), the LEDs are stuck in a cycle where they alternate between cycling colours and blinking green.The Primary AP (AP6C41.0E22.0908) ...
What does the red dot - "uncontained" indicate on an SSID identified on the Air Marshall Rogue list?
Hi Experts,people are complaining about poor connectivity -Is channel usage going high an issue?Please suggest me solutions
Resolved! Which WLC for AIR-CAP3502I-E-K9
Hey guys, I currently bought 4 Air-Cap3502I-E-K9 for my home setup and run them in autonomous mode.Now I‘m wanted to run them with a WLC but got absolutely no idea which one is the right one. What do I need to look for and which WLCs would work with ...
Configurei a AP air-cap3502e-t-k9 pelo CLI, com comandos simples de IP estático, definição das redes dot11Radio 0 e 1. Defini as redes de 2,5G e 5G, e conectei direto com o roteador WLAN.Ele funcionou bem durante umas semanas, só que agora ele derrub...
