Wireless

I am located in an 85 year old hospital. Running cable for new PC's is getting very expensive. I currently have 802.11b access points for roaming users. Is the new 802.11G a viable option for a permanent, everyday work PC? Is anyone out there usi...

Should the WDS be able to see AP across different networks ( different vlans )? I have 40 or so on one WDS with all the same network. I have added 3 new ones on a different network and they don't see the WDS. WLSE can see them just fine and they a...

I recently upgraded my 1200 AP's from JA4 to JA15. Upon doing so, my 350 WGB's no longer receive connectivity from the 1200 AP's. They appear to associate with them but i cannot ping the bridge nor the workstations assocciated with it. When I down gr...

Can anyone help we are currently using Aironet 1200 AP and .11a/b/g cards for laptops, with ACS 3.2 and Microsoft Server 2003 (CA).We cannot get PEAP working yet LEAP will, we have configured everything certificates, AAA clients on ACS etc etc... bu...

I want to install 1300 series ap/bridges but I have notices that the 1300 is not mentioned as a spported device for WLSE 2.5 or CiscoWorks 2.2 Will the 1300 be discovered and managed as another AP?

Hi,I have some questions regarding 802.11g and 802.11b infra.Scenario AThe wireless LAN infra is 802.11g access point which supports up to 54Mbps bandwidth. There are 10 clients with 802.11g card. They are 10 metres away from the access point.Scenari...

Does anyone know of any situation were a bridge would revert back to its default configuration. Other that pushing the reset button. Please advise.

Hello all,I have Pocket PC PDA ipaq that i want to bring on wireless network (802.11b)the details are as follows 1) PDA Device - Compaq iPAQ Pocket Pc 3600 using the expansion sleeve for CF slot . The details as mentioned in the URL(http://www.the-g...

I wanted to know if the new VXworks image (12.04) fixed the issue that was in Vxworks 12.03 that prevented upgrading to an IOS image. I had heard that if you uprgraded your APs to VXworks 12.03 you could not upgrade to an IOS image...you had to go b...

We are seeing intermittent authentication failures on mobile carts. Most times, this is associated when the PC is re-booted.We are using Win2K clients with Cisco cards (ACU ver 1.1.10) Cisco 1210 AP's with G installed IOS ver 12.2.15.Roaming works w...

Hello,I need that the Radius Server (Radiator) assign an IP address to the client that connects to one AP1100 (IOS 12.2).Despite the Radius register that send the IP Address to client, thiss don't accept the IP.** Sending to 172.29.3.1 port 21672 ......

Dear FriendsI found some measurements of Loss or Gain of signal strength with negative sign (like -85 dBm, etc.).When is a negative value of this unit of measurement used and what does it signify ?What is the difference between dB, dBm, dBi, dBd ?And...

Hello,I have a PC that connects :- When connecting to wired LAN boots normally : 2 min max- When connecting to Wireless LAN, the PC may take 20 min booting (before even openning the session and bringing the VPN tunnel).I have trace the boot phase on...

I have a 3Com Workgroup bridge attached to an AP350, but the AP constantly send this warning "Host 000b46f357a9 not allowed on port "fec0""Besides the clients attached to the 3Com Bridge constantly are off line, we need to reset the clients every tim...

Hi,I am woundering if someone could help me, actually I was trying to upgrade my ap1200 with the latest image (c1200-k9w7-tar.122-15.JA.tar), while upgrading, it stops automatically, Now when I rebbot it, it show as below:ap: Xmodem file system is av...