Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
Does anyone know what the default power level is for 1240AG's in U.S.?I've looked for it in documents I found on cisco.com but they only tell you what the max power is and how to configure them.Also, how do you see what the current power level is in ...
Dear all,Is there any limitation on the # of user connect to one AP 1240?Besides, can I use the cisco aironet site survey utility without the cisco adaptor card?Thanks.C.K.
Anyone tried Cisco CB21AG Card with WZC WPA configuration? I can configure and use WPA with ADU no problem. But when tried with WZC, no WPA option available. The computer is XP SP2 and the card is with latest driver 3.0.Thanks!
My APs disassociate from WLC every hour, so I completly lose the connection.0 Fri Sep 8 17:29:09 2006 AP Disassociated. Base Radio MAC:00:17:0f:da:f2:60 1 Fri Sep 8 17:29:09 2006 AP's Interface:1(802.11a) Operation State Down: Base Radio MAC:00:17:0f...
I am trying to set an aironet 1010 for use in a site survey. In my class, the book showed a jumper under the access panels. These APs do not have the same set of jumpers. J31 has 3 sets of pins while J49 has 2. can I set this 1010 up to run independe...
I am looking at using the WLSE to manage about 15 1100 and 1200 APs. These APs are on varying VLANs on my network. I am looking at having "public" and "corporate" SSIDs on each AP. Will I be able to manage all of these APs and SSIDs across multiple V...
HelloWe are trying to implement EAP-SIM with Radius (Lucent Navis Radius) and the Cisco AP 1200 and the "Option GlobeTrotter Fusion+" PC Data Card.In the datasheet of the AP 1100 I found the support of EAP-SIM. But I didnt in the datasheet of the 120...
I just bought a aironet 1200 and a 10 DBI YAGI antenna, problem is I cant communicate with clients connected to my aironet 1200, I can ping via the aironet command line but not with computers behind my ap.Is it most likely a config error or has someo...
I am trying to build a template for our AP-1010 access points. Whenever I click the "apply" button, I get an error message that says the following in the the 802.11b/g Parameters area: Failure: MEDIATION-1, Attempt to set conflict attribute value, Lr...
HiI have 3 AccessPoints 1242AG running on the same subnet. To keep it simple I configured only one AccessPoint acting as a Radiuserver and on the other 2 AccessPoints I point to the correct AccessPoint(the one with the Radius configured). But when I ...
Hi,we have Cisco ACS Running for authentication based on Mac-Address, and I was questioned if the future is to use CiscoACS or something else? because if it is CiscoACS, then we will invest on a redudant Server. Did you ever done such configuration?
Hi, need to configure 2 SSID on the same 1100 AP: open authentication and WPA2. It's possible to configure these 2 SSID without configuring VLAN's ?On CCO I've read the following:http://www.cisco.com/en/US/products/hw/wireless/ps430/products_qanda_it...
I am always getting the ''Device was not reachable via SNMP'' error messages from wlse , i confirmed the devices were up & running is there any setttings in wlse i can rectify this error messages.
We have a site with 3 controllers it's serveral miles between them. And have think about to deploy a N+1 solution. My question is if the controllers must have same RF group. I know they must have same mobility group!. Can you have several mobilty gro...
I am trying to setup a guest network on our wireless lan. We have 2 vlan's setup for wireless. vlan 1 is our network and vlan 10 is our guest network. We are running 1131ap's and 1121g's. I have been able to get most of the 1131's working, but I can'...
