Hi guys,Is there a Cisco a/b/g integrated diversity antenna with 4 cables that a Cisco 1242 AP can support all the -a and -b/g client with only one antenna?Thanks,yytellmey
Hi guys,Is there a Cisco a/b/g integrated diversity antenna with 4 cables that a Cisco 1242 AP can support all the -a and -b/g client with only one antenna?Thanks,yytellmey
Hello,We have installed 40 AP in our building, thus using Cisco 1010/1020 Ligthweight AP and 4400-50 series Contollers.In some places, the laptop connect sometimes to bad signal AP instead of the one beeing vary close, thus bringing vary bad connecti...
We are upgrading 800 APs to lightweight. I know the upgrade tool can only upgrade 6 APs at a time. Can I run the Upgrade tool on two different computers at the same time so that I can upgrade more than 6?
I have a question, I'm pretty familar with 802.11B Networks, I however am slightly confused when seeking to develop an IP Oriented solution for a Carrier Company we're working with. They seek utilization of Mobile IP within the following context. The...
AP1030WiSM 3.2.116.21I have an AP1030 that is losing connectivity to poor SNR. (I'm fixing that, the antenna was installed incorrectly)However, while Diagnosing it, I found this in the message logsWed Aug 23 18:30:49 2006 [ERROR] spam_lrad.c 1799: AP...
I've upgraded the software on my AP1231G-A-K9 with c1200-k9w7-tar.123-8.JA2.tar.The AP seems to work fine but when using QOS Voice scenarios I'm having a lot of problems that I don't see when using AP1232AG-A-K9 with the same software version.
Looking for a good program to convert AUTOCAD .dwf files into .jpg for importing into WCS. Having issues with Visio. Thanks
I configured my 1130AG as a DHCP server. The WAP is on a vlan. I am connected to a 2801 through an HWIC-4ESW-POE. My clients connect but I cannot access the Internet. As part of the DHCP configuration I identified my default router(gateway) using the...
I have observed newly-installed LAP-1131AG access points that have been "primed" to a particular controller. When we boot them up with the same WLC controller to which they are primed, they eventually turn light green (which according to the document...
I have a 1231G autonomous unit and a 4404 wireless controller, both reside on the same subnet, the controller is in layer 2 mode and has the bare necessities configured at present. I converted the 1231G to LWAPP, which was successful. But the LWAP wi...
Greetings,If I have two different WLANs, both configured for WPA-PSK, are the pre-shared keys different per WLAN?I ask because when I change the PSK on one WLAN, it seems that this may be affecting the other WLAN.I'm not on-site to test this out, unf...
Hi,I would like to setup 2 branch with hybrid reap access point.I did standardize the vlan assignment for the hybrid reap access point ( let say vlan 2).Since all the configuration done through WLC. Is there a way to configure using the same vlan id ...
Hello everybody,I am a bit confused about cisco 1000 series access point connection. On wireless lan controller and lightweight access point basic configuration example document id 69719 (http://www.cisco.com/en/US/products/ps6366/products_configurat...
We have a (brand new) WiSM blade installed in a 6509. The configuration looks ok, but when we try to register (join?) an AP with the controler the process fails. The controler shows the AP in the status display but the AP reboots, claiming that no jo...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 11-16-2026 05:39 AM | ||
| 10-15-2026 05:58 PM | ||
| 10-12-2026 06:46 PM | ||
| 09-30-2026 07:34 AM | ||
| 08-10-2026 11:32 AM |
| User | Count |
|---|---|
| 5 | |
| 2 | |
| 1 | |
| 1 | |
| 1 |