Wireless

Hi everyone,In what way disabling the SSID in beacond would affect my wireless network performance and functionality? Thanks,ME

Hi,Can I use windows XP to configure EAP-Fast? or is EAP-FAST only configured on the ACU 6.3 utility.I have a different vendor wireless card with a AP1200.I want to use EAP-Fast.Is this possible or do I need to use PEAP or EAP-TLS?regdsJohnny

I am targeting to have an Aironet 1300 solution for an ISP. But I wonder if Aironet 1300 bridge, in point-to-multipoint mode, allows me to offer different bandwidths, e.g. 128kbps, 512kbps, 2Mbs .. etc to different locations?

1.I have 900 yards to bridge two bulidings can I set up two Cisco 1200 AP'for that bridge?2. Point to multipointI am bringing up a point to multipoint network, besides setting; data rates @11mbps, turn off broadcast SIDD, set point as ROOT and multip...

Has anyone out there had any luck with getting the Cisco Aironet 350 Mini-PCI working on an IBM laptop with Linux? I have it working fine with Windows XP Pro but would like to get it working with Linux. Currently have RedHat 9 ( 2.4.x kernel ) inst...

AP1200 with IOS 12.2(15)JA upgraded from VxWorks 12.03T - Problem: When the units are booted they do not reveive the IP that is reserved for them. They register with a very long (24 bytes) number instead of a 6 byte mac address. If I check disable dh...

I have several Cisco 1200 Series AP running IOS JA4. I also have many 350 WGB's running 8.85. When i upgrade the AP to JA15 the WGB's associate with the AP's however the clients connected to the WGB's dont have any network connectivity. All of the se...

Hi, does anyone have a good link explaining all authentication and encryption methods and when they should be apllied.Thx

I set up my AP with internal 802.11 b radio for Basic-5.5 and Basic-11.0 and disabled the other speeds.If I only have 11 Mb/s clients, I'm assuming that the AP will transmit the Beacon at 11 Mb/s. However, if one of my clients roam and can only suppo...

I have a cisco 2950 with 5 x Access Point 350's connected to it. The first access point in connected via a UTP cable as its was within 100Mtrs. The other four, are connected via fibre cable and media convertors. I have lost ethernet backbone conne...

I am trying to import images to my wlse and keep getting this errorDevice type: AP1200-IOS, version: 12.2.15-JA. Image import failed. Imported file is not a valid image.Device type: AP1100-IOS, version: 12.2.15-JA. Image import failed. Imported file ...

I am trying to configure 4 VLANS on 350 WGB's. Under privacy configuration settings, I am only allowed to enter the wep key for one VLAN. Is it possible to use multiple VLANS with 350 WGB's?

I got this log message from one of our root bridge:2004/08/04 16:15:21 Warning Network Bridge Loop: Received packet from Self destined to [AWC Mcast AP-Only]014096ffff00 on port "fec0" What does this mean ?need your advice

HelloI'm having a problem with installing the CB21AG card. I'm using the new 1.1 ADU and ACAU to preconfigure the driver installation to have some basic settings. However after the reboot when the user logs into the Novell ctrl-alt-del screen it hang...

We are installing wireless, it is going to just be an extension of our current lan so people with laptops don't have to plugin..my question is.. we have all the equipment here.. is there anything else we need to do besides install it?