Wireless

Having a CCKM issue that is really annoying my customer. TKIP is configured with CCKM and is using LEAP for authentication. A WDS is setup and works great except for these issues. Clients attach and roam but 1-2 twice a day up to 6-8 times a day, cli...

I have (2) networks going into an ap 1200 - the AP has a static ip set on it as 192.168.199.210 which is vlan 20the other network is from my DSL to have wide open wireless for guests (vlan100) that ip in the router is set at 192.168.199.51 (scope is ...

If I bought the current WLSE product (CWWLSE-1133-K9), this comes with software 2.13. Would it be possible to downgrade the software to 2.7.1, which is what I have tested and certified?

Does anyone know of a config example for LAN (VLAN1) off F0-3 plus AP Wireless Access on a Cisco851W?Thanks,Bob

Has anyone else experienced an issue with the AP1131ag access points flooding the network with igmp packets? I have an AP1130 already in service which did not cause this to happen. And this has happened with 2 AP1131 that I have taken out of the box....

Hi All,I have been checking the "Cisco Systems Aironet 1310 Intallation" manuals, and have noticed that the external antenna model has connectors for two antennas.My question is if this device could be used as repetitor (logically splitting the signa...

Hi ,I am testing basic L2 LWAPP and am having problems getting the AP's to register with the controller.If I run a "debug lwapp error enable" I get the following error message:"Mon Jun 5 17:22:00 2006: AP 00:0b:85:24:89:d0: Regulatory Domain (0x0001)...

Well..I have the following devices:WCSWlan controller 4402AP 1130 LWAPPWorkstation XP sp2Secure ACS 4.0Windows CA Windows AD---------------------Everything else is working properly, except EAP-TLS. Server certificate is installed in ACS and trust lis...

Hi people,I´m installing 3 AP 1232(dual), documentation says they support 802.11a/b/g, they support it at the same time or it is up the anntena ?Martin Cordero

I am proposing to install three AP1242 and want good coverage within a warehouse, so am looking at the ANT-2460P patch antenna. Do I need 2 of these per AP and how far apart should the antenna be placed apart. I need to cover a working height from 4 ...

I am installing a second WiSM blade on a redundant (backup)6509. The A&B side of the produciton WiSM were spec'd to run <= 300 APs. How does one configure these control units so that production runs on WiSM blade 1 and fails over to WiSM blade 2 on t...

I have many existing buildings with AP's already placed on floor plans.I would like to add them to Campuses. Is there a way to assign the existing buildings to new campuses without recreating everything?

We are building a new site and we are planning on installing a WiSM at the main site. We also have 9 Branch offices that are connected via CSME (OPTEMAN) on 2821 routers at speeds ranging 10mb - 100mb. Question: Can the WiSM control AP's at the branc...

Hello everybody..I`m already designing a point-to-multipoint bridging with Aironet 1300. On the central site I have a omnidirectional antenna and on the remote site integrated antenna. The question is: How much bandwith could I get if my topology is ...

What is the difference between AIR-AP1232AG-E-K9 802.11g IOS AP w/Avail CBus Slot, ETSI Cnfg AND AIR-AP1231G-E-K9 802.11a/g dual radio IOS AP, ETSI cfg ?Both part numbers need to order Antenna separetly ?RegardsMohamed