Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

review


Labels

Forum Posts

Hi,I am trying to get a 1200 setup as a repeater and have run into a problem, any help would be apprecaited.I have 3 vlans setup for wireless on site. One for radios/infrastructure, one for valid users with regular logins, and one for guests that jus...

millerlw by • Level 3
  • 761 Views
  • 1 replies
  • 0 Helpful votes

A customer wants Wireless access in a small area which is 250 yds outside their door, across a parking lot. My question, would signal from a 1200 WAP, with mast mounted antennas, reach this area or should I setup a bridge?

edwardsjj by • Level 3
  • 991 Views
  • 1 replies
  • 0 Helpful votes

Does this message necessarily mean that the flash memory is damaged?AP#sh flash:Directory of flash:/%Error opening flash:/ (Invalid argument)No space information availableThanks.

carlossal by • Community Member
  • 867 Views
  • 1 replies
  • 0 Helpful votes

I know that the power on 1310 is 20 mw for both cck and ofdm. On last bridge I saw (ios 12.3.7), I found out that these values changed: 50 mw for cck and 30 mw for ofdm. I tried to upgrade an old bridge to the new ios but the values didn't change.Wha...

fgiarlo by • Community Member
  • 617 Views
  • 1 replies
  • 0 Helpful votes

HiI need to purchase a wireless access point and it will only be used to transmit data and nothing more. I have restricted my choice between a Linksys WAP54GP and Cisco Aironet 1100 but can't make up my mind on which one to buy. What does the Cisco b...

tyeung by • Community Member
  • 1137 Views
  • 1 replies
  • 0 Helpful votes

I am looking at connecting to a wireless ISP that has a tower just below my house, the signal strength is high enough that I can connect with a standard wireless card without having to use an external antenna. I would like to install a wireless route...

NPT_2 by • Level 7
  • 451 Views
  • 0 replies
  • 0 Helpful votes

I know this AP ships with a full IOS but here is my design question. In another setup, I have used a similar AP as the default AP on the wifi network, but have used a PIX as the default gateway.On this network, I don't have a PIX or another router to...

I have implemented WLAN in a four floor building as per the following e.g.:-vlan 2 - 1st/3rd floor subnet 2.x.x.2 /24 - SSID Corporatevlan 3 - 2nd/4th floor subnet 3.x.x.3 /24 - SSID Corporatevlan 4 - all floors guest access subnet 4.x.x.4 /24 - SSID...

j-tyler by • Community Member
  • 943 Views
  • 3 replies
  • 0 Helpful votes

We are installing our first NM-AIR-WLC6 module. The router has very strict ACLS applied to the AP facing fast ethernet interface.The LWAPP documentation list the ports required to be open for WCS to WLS communications, but does not list the ports nee...

mdeloach by • Level 4
  • 1076 Views
  • 4 replies
  • 0 Helpful votes

HelloWe tried to authenticate the radius user request from a wireless controller 4402 by a novell border manager 3.6.The border manager was not able to understand the request and got back the error(-803)no such user.This behavor is equal for LEAP, WP...

keynet by • Level 2
  • 984 Views
  • 2 replies
  • 0 Helpful votes

Since there is little documentation on the Airespace controllers, I thought I would give this forum a try a try.I keep receiving this error:x_auth_pae.c 2367: Reached Max EAP-Identity Request retries (21) for STA 00:13:XX:XX:XX:XX

cplatt01 by • Level 7
  • 690 Views
  • 2 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card