Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Hello - I have a version 3.2 of the ACS appliance and I am trying to set up a successful test of EAP-TLS. I have a W2K server for a CA and I believe I have the certificate install properly. However, I get the "EAP-TLS or PEAP authentication failed du...
Hi,I am looking for a list of supported MIB by the Cisco Aironet 1130... I have searched in this site but I haven't found it anywhere.Thanks you by advanceKhay Huynh
I have a 350AP with 12.00T, using "Aironet VxWorks to Cisco IOS Conversion Tool" I upgrade to IOS 12.2.13.My PC has a "Intel 2200bg", I see SSID "tsunami" but I can't connect.Ethernet led light greenStatus led blinking greenAs start of point, I don't...
I have been trying to get a Aironet 350 MiniPCI working with WPA-PSK . [IBM T41 notebook, WinXP SP2].I have got another (older) notebook [HP nc6000 with winXP SP1] working without problems so I am confident of the overall access point setup.However, ...
Has anyone found a good link on configuring guest tunneling using the new Cisco lightweight wireless architecture? I believe the basic concept is to transparently tunnel guest traffic directly from the private wireless network to a wireless LAN contr...
This is an update of a previous post .I have a aironet 1230 B and he is dropping clients and i´ve found that he is only dropping AP´s in client mode and only the D-link 900+ ,there are other D-link Ap in client mode and don´t have this problem .I've ...
I have noticed that when my 7920 is roaming, it looses connection with the AP.My AP has the very basic config, open authentication with a wep key on the SSID for voice and data vlan. I also have qos configured and applied.I have read in this forum th...
Is it possible to use a Yagi on the 5GHz radio (for bridging) and use rubber ducks on the 2.4Ghz radio (for AP)? In other words, does each radio have its own pair of RP-TNC connectors? Thank you.
Hi,I'm trying to setup an 1200 AP; the problem is that I get no reponse from the default IP 10.0.0.1; I've reseted the AP, verified the switch and the ethernet wire, but i can´t connect to the AP. And I have not a console cable..
Folks, We have an access point, we have configured multiple vlans on it, for some reason when i create a new vlan and associate a ssid to it, the hosts can not obtain ip addresses for that ssid, i am using A radio and using WPA2.Any Advice would be h...
In the overview section of 12.3(7)JAConfig Guide AP 1200 there is a featurementioned called Frame Monitor Mode.Does anybody know how to configure/use it ?
Hi,I've been working with a wireless network, where ap 1200 are being used as repeaters and ap1300 are being used as root.Sometimes, some of them get hanged, and must be reset.The software version of the ap's is 12.3(7)JA2.Here I attach a crash-info ...
We have a Cisco 1130 WLSE appliance, recently purchased. We had trouble trying to configure it via the console so we decided to rebuild it using the supplied recovery CD (version 2.11 WLSE 1130-19) to make sure that the installation was okay. Two day...
Is there any Wireless Card Capable Router.I need to purchase 2600 and 2800, Do Cisco offer wireless card or network module for these routers.Thanks
Anyone know how to get a config job to push changes to the router side (session15) of the 6500 series?
