Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
The hardware specs for the MR36 say that it can do the 160MHz bandwidth... is that available in the firmware and enabled via Support only? It is not in the dashboard.
Hi Freindslet's say the user Connect to SSID , Where to check the ARP of the user connected to this SSID , on the Core or some where else , pls be note the AP is configured on Local Mode Thanks
I'm hoping there is someone that might be able to help me with my issue. I followed the guide down below to create an SSID that would do CWA for a client with ISE 3.2. My WLC is 17.9.4a.https://www.cisco.com/c/en/us/support/docs/wireless/catalyst-980...
HiI have a 8540 I want to move from an older Cat6k to a new Aruba 8360. The 8540 is running an older train (8.3) and is configured as a LAG. Since there is no negociation or support for LACP or PAGP on the WLC, I've forced the LAG port on the Aruba s...
Hi All, Is there a way I can see the RF neighbors from a AP joined with the WLC, can the show controllers dot11radio 0 will help in thisRegardsNikhiL
Has anyone set an SSID with OWE security and Splash page Sign on with My Radius Server (Radius server is ISE in my case), I don't even see any log coming into ISE, I know communication is working because my radius tests are successful. I tried with p...
We are using WLC 5520 controller and now want to join AP CAT-9105. As per datasheet it should support.But can anyone confirm it will work or not or any specific configuration needed?
Also could someone tell me the speed of clients as number of clients go up.
Hello,I have few Windows 10 devices connecting to WLAN that’s WPA3 only . I’m using AES CCMP 128. When I look at the WIFI settings on the laptop it’s showing WPA2-Enterprise. But this WLAN setups to accept WPA3-Enterprise. I am using windows GPO to p...
We have currently 2 Cisco 9800 on prem CL-Controllers running version 17.3.5. Site A WLC is primary for endpoints in Site A and Site B is secondary WLC for endpoints in Site A and Vice versa. In our current setup we are running on low VM resources (H...
Is there anyway to see what the actual operating data rate/MCS/streams are for a connected Mesh AP? Seems like something that would be useful to know before doing testing but I cant seem to find that information via 9800 CLI or GUI. The show mesh bac...
Hello Cisoc WLAN experts,I habe noticed that our good old Prime 3.10 is not showing WLAN AP outages correctly in conjunction with a 9800-80-WLC running 17.9.3 code with around 1000 APs on it.The WLAN AP outages themself are shown correctly as an Alar...
Hi ,The Cisco Catalyst IW9167 AP was introduced in June 2023; however, I have not been able to find it listed on the regulatory domain list. I have been searching on the following link, but with no success:Link: https://www.cisco.com/c/dam/assets/pro...
Hi,I was trying to run just plain simulation of Signal Coverage patterns on Ekahau for CW9166 and MR57 and match the propagation patterns with Datasheets just to see how good they are when being compared to datasheet Coverage patterns. Please note , ...
This is just a notice in case anyone else has the same issue while they have the Early Access Program feature of 'Dsign System' switched on.If you try to add a RADIUS Server to a 802.1x SSID and then save your changes, you may receive the following m...
