Wireless

I am currently using (2) 2621 routers as edge routers. The first connects to ISP-A and the other to ISP-B. The first has (4) T1 lines the other has (1) T1. The first is configured to obtain NTP from the same two locations as the second, however fails...

I have a AP1100 with a G radio that is giving me the following error:" %DOT11-3-POWERS_INVALID: Interface Dot11Radio0, no validpower levels available"from the web interface the radio settings are all messed up (see attachment) and it says it's a B ra...

Noticed recently that I have 4 1200 AP's with the radio mac addresses showing all zero's. These are b radios and this just appeared. Any ideas on why would be greatly appreciated.

I had refer http://www.cisco.com/en/US/products/hw/wireless/ps430/products_white_paper09186a00800b3d27.shtmlIf the ACS server used for MAC authentication whether only for used LEAP authentication, in other word mac authetication don't support EAP or ...

WLSE 2.11AP: 123-2.JA2Hellowhen I do a unicast rekeying from the ACS every 120 sec (atr. 27), then I got on the WLSE > reports > wireless clients > historical association an event called "roam" for every re-keying time (120 seconds). This seems for m...

We have deployed access points 12000 series through out several departments with roaming enabled. Now we are in need to somewhat manage the growing wireless LANs. We currently have installed Solaris LMS2.5 for configuration management of all our Cisc...

Hello,we are using guns Teklogix with embbeded cisco card associated (model CB20A) with AP 1200.It worked very good : no loose communication.We were using two radius server AP with LEAP.We did few changes one month ago :-> changing ip adress of gun (...

WPA isn´t supported in Windows 2000 yet. Is it possible with a Cisco Wireless Card and the Aironet Client Utility to establish a WPA1/WPA2 connection?

Hello I'm looking for some software to manage and monitorize a group of Cisco AP.Can you recommend me any soft or link to get more information?Thanks

dear alli have 2 offices distance between them is 3.5 kilometers. i want to link between them thru 1400 series bridge.but i'm not clear abt the location, bcoz the next office is 3.5 km away so i dont know which side it is, so in this case, how can i ...

I am having a problem with a WLSE 2.11 template on a 1210 B/G Access point running IOS 12.3(4)JA. I am configuring as follows:The encryption for the VLAN in question (I will refer to it as VLAN X) is Cipher/CKIP.The SSID config for the VLAN is EAP, n...

HiI would like someone to confirm my knowledge of the behaviour of the WGB 350 with the population of its mac-address-table.My customer uses the WGB to connect multiple industrial PCs to the WLAN in a big hall. The PCs are placed wiedspread, and when...

Hi , I have had continously message of this in a syslog :Jun 18 11:11:46 192.168.4.216 5595: *Mar 3 21:03:39.726: %DOT11-4-TKIP_MIC_FAILURE_REPORT: Received TKIP Michael MIC failure report from the station 000f.f778.e28a on the packet (TSC=0x16000000...

hi guys,Does cisco have any wireless frame capturing softwares? I mean the technical stuff. the software must be able to capture frame format e.g (frame control, duration, da, sa,bssid, sequence control, ssid IEe, support rate ie, etc....ive tried et...

HiI am looking for an access point that can also make a serial (9 pin) connection to a GSM modem. Any one have any ideas??RegardsMalcolm