Wireless

Hi all,I´ve APs 1100g and want to configure WDS just only to authenticate theses APs (to radio manager on WLSE), but when enable WDS to Infrastructure Authentication :ap(config)#wlccp authentication-server infrastructure method_XXXXthe client authent...

As now it is unfortunately not possible to enable "guest mode" on more than one SSID/AP. However - I heard something that this feature will come during the spring so that severel SSID's can be announced in the air. Anyone know about this?Anyone know ...

I've been working with WLSE for a bit, and I've enabled radio monitoring in WLSE on a few AP's. I was wondering if anybody knows what the cost of doing this is. Does this affect bandwidth, or radio signal strength etc...? Thanks for any input!Mike.

Is it possible to have 802.1x windows 2000 machine authentication and user authentication leap on the same PC.I want to have the double layer of security where the PC boots up and authenticates via MAC address. This would enable scripts and machine p...

Hi,will the Aironet1300 Bridge support a proprietary 108MBit/s Turbo-Mode for P2P or P2MP in the future?best regardsAngelo Brancato

Hello,We've recently bought a number of 1131AG APs that come with 12.3(2)JA2. I upgraded one to 12.3(4)JA and now the 11g radio won't come up, I've tried downgrading back to 12.3(2)JA2 but the radio still won't come up.The console log during boot is ...

We've been using wireless networking for quite some time, but at the time it has been installed without the use of WDS. I'm preparing to change this on about 17 locations. Some have a few AP's, but others have many (one has as many as 82). So, what I...

I'm slightly confused. The Cisco docs for the latest IOS release seem to state that AES is working in this release. The Intel docs claim that the 2200BG client card is also enabled for AES. When I connect the two using WPA-PSK, they maintain a solid ...

Hi Sir,Good day to you. The following paragraph is extracted from Cisco recommendations, To ensure that the wireless devices function properly, certain environment condition has to be taken into considerations. Since the wireless equipment is mounted...

I have a Cisco Aironet 802.11/a/b/g PCI card. When I try to log on to our company domain through the wireless connection, it gives me an error saying that the domain is not available. However, if I log on using a wired network connection, I have no p...

Hi, i've just been told that if you use an 802.11B radio on an 802.11G network and the modulation is CCK then the 802.11B clients will share 11mb but 802.11G clients will still get higher throughput.Is this correct or will ALL clients share 11mb if y...

Hi,We have deployed an EAP-FAST solution with two Cisco 1200 Series access points and Cisco ACS server. We use three VLAN's on the wireless side, one for guest access to the Internet, one for corporate data access and one for voice access for our Cis...

I use BBSM ver 5.3 with RADIUS (ACS 3.0). we need to use password aging options ,when user logon first time the BBSM request change password.Currently when user logon first time it connected but RAIDUS account is expired after first logon.Does BBSM c...

I am trying to configure PEAP and machine authenication against a windows nt4 domain. The machine authenication fails against the domain. The username is successful. I am using Cisco 1200 and Cisco ACS. Any suggestions?

Hi,I'm setting up PEAP according to this documenthttp://www.cisco.com/en/US/products/sw/secursw/ps2086/products_configuration_example09186a00801df0e4.shtmlI have AP1231 and ACS vers 3.3 and I have set ACS up with a valid certificate from Thawte.My qu...