Wireless

I am running 1.1(1) on WLSM and cannot specify extended VLANs like 2001. Does version 1.2(1) support extended VLANs? If not what timeframe can I expect to see extended VLANs.

I'm running ap1200 with ACS 3.3.My scenario:Vlan2, 3 and 4 - LEAP & MAC authenVlan5 and 6 - MAC & Static WEPVlan7 - MAC AuthenVlan 10 - ManagementVlans 2, 3 and 4 work correctly. Same with Vlan 7 and 10. Vlans 5 and 6 are a problem. No association to...

I have completed a couple of small tests with the Cisco 1410 bridge setup inside a glass window.to a 125 foot tower at 800 meters away. It appears to work OK and saves a lot of problems when it come to weather and access. Is this a reasonable setup? ...

Wireless newbie here. I was told not to ever provide the power source to a wireless bridge (350,1310 and 1410) until after an external antenna was installed on the bridge, prior to configuring the bridge. Simple enough to do on the 350 or 1310 but th...

I have a customer who wants to link 5 out buildings back to the main network. I have proposed using the new 1300 series bridges and have already verified clear line of site from the root location to all remotes. The customer wants to run VoIP and dat...

I've been in search of a way to get my NTSC video stream onto a PDA. One solution seemed to be to find a device with video inputs that would then stream it over 802.11. Does anyone know of a product like this or another solution to my problem?

Hello there,We have 10 Aironet 340 Access Points and we have been trying to implement wireless vlans. We have set up 2 vlans one with encryption and one without. We can get an IP address from all of them and can ping both the AP and the gateway, but ...

I need to disable SNMP on our complement of 350 APs. However, I've tried the normal route of disabling via the SNMP parameter (web) page but if I go back to the APs a day later somehow SNMP has re-enabled itself. I've tried turning off CDP to help th...

I would like to change the hostname on my 7920 wireless phones, because the default name consisist of SEP00mac-address. (see network settings ->current config).Any input is very welcomeOliver

Reading the setup specifications I see that the distance setting should be 99 when in Install Automatic Mode and should return to 0 when changed to ROOT. When looking through my settings the distance setting is 2 km. Does this cause nay problems for ...

Hi.Im having some trouble using the aironet 350.The thing is that i can connect to the internet, but some times i lose the connection. I like using instant messaging, but with this problem is impossible, cause it signs out all the time.Im using the h...

Hi,I have a very strange problem with the radio channels of my radio B interface on ap1200.we are starting our Wireless Service in our library. We are running PEAP. Everyone, can log in fine.But when I do the carrier busy test, it shows that channel ...

1210 b and g radios ver 12.2(15)XR2WLSE 1105 ver 2.7.1I've been testing the use of scanning-only AP's and I have a couple of problems that level one support has been unable to assist with. First is that the documentation implies that you can set up a...

Is it possible to setup 2 AP1200 in a bridge mode?For examplePC ----switch----AP1200 --- Antenna (( )) Antenna --- AP1200--switch---PC I'm trying to setup a link (wireless trunk) between two buildings, I have 2 ap1200 and antennas that I could use fo...

i have two 1200 ap's, one as root, the second as a non-root repeater ap for testing purposes. they work well but they do not roam that way i expected. i found out that the client changes the active ap when the signal strength is getting very bad, not...