Wireless

I have installed 10 Aironet ap's throughout the bldg. All ap's are mounted from ceiling with antennae pointed down towards floor. I have been asked what the radiation pattern is for the antennae. I'm using 2 dipole antennae that is standard for the a...

I am having a delay authenticating to my Aironet 1200 when first logging on using WPA to ACS3.3. My login scripts are not executing because of the delay. I installed the Microsoft patch KB826942, but still have the problem. No delay if I logoff then ...

Hi bruce, we've implemented a wireless network in a school recently. there are about 30 access points covering the whole school but due to the construction we can see about 11 access points at any one time. my question is reagrding channel set up. we...

Have set up 2 VLANs on the AP but can only access the one that has it's SSID broadcast in the beacon. If the VLAN does not have it's SSID broadcast it is not seen by the laptop (tried 3 different one and a PDA). Can swap which SSID is broadcast and e...

I have an issue where a Cisco cardbus adapter causes a PC BSOD on whatever PC or different Cisco card is used. This only happens with Cisco a/b/g Cards and 1230 APs and only in a certain AP area of the building.Has anyone else ever experienced this?

Hi- Is it possible to Change MAC-Adress of a AIR-PCM352-Card ?my driver version is 7.29.0.0 (01.07.2001)- How can i update the firmmware of this 802.11b-Client-Cardis this possible with Tools ACU 6.3.011regards,Ralf

On the RadioG settings :CCK Transmitter Power (mW): 100 MaxOFDM Transmitter Power (mW): 30 Maxwhat is the difference between setting it to Max or to 30 or 100?They would both seem to be the max.

hi all,i've a problem with my Aironet adapter 350. My problem is that i could not use the 128 bit for it.i just can choose 2 value 40 bit and 104 but not 128bit.my laptop uses window xp.

I have just inherited the network which houses a 340 Bridge with early 8.08 firmware. My problem is, the previous administrator password protected causing the configurable attributes to be readonly while I connect with a serial cable.I really need to...

I have a client that asked me about a situation where they have a school with three floors and around 6 classrooms on each floor. It's a small school. A company wants to install 21 Cisco 1200 AP's in each room and in the hallways. The school wants al...

Hi, muzhiki!I have AccessPoint Cisco AP340. And i whant to get statistic to Linux by SNMP. I set SNMP Trap Destination and SNMP Trap Community. But, when i run command on my Linux-box (snmpwalk -v 2c -c XXXXX aaa.bbb.ccc.ddd), he not answer to me. Wh...

I have an AP AIRONET 1200 (802.11a and 802.11g) and 2 Clients. One Client with a 802.11a-Card works fine. The other Client (AIR PCM352) works (Windows CE dot.Net 4.2) with 802.11b could establish only one Connection. If the Connection is broken (beca...

Anybody knows how Cisco pcmcia wireless card work with rehhat 9? My Redhat 9 can detect every other cards but cannot detect my only card with exactly the same type. The reason is not my card spoilt because the card works well in Windows environment.

I'm setting up a WLAN using Cisco AP1231G-A-K9 access points. I'm using Cisco ACS 3.3 for 802.1x Radius authentication and authenticating using Active Directory.I have Dell Wireless and Cisco Aironet 350 client adapters working perfectly, but I'm hav...

When switching from battery to AC (or back) on my IBM T41 laptop with embedded mini-PCI Cisco WLAN adapter, I lose the IP address after about 30 seconds, and must "repair" to regain it. Using WEP with an open key. When troubleshooting, a PCMICA 340 a...