Wireless

Does any one have a problem with Toshiba portege R100 on connecting to WL Cisco AP-350 it is associated with the AP but does not get IP address, after a few play with network configuration it work ok but next time of reboot the same problem again, al...

I am just beginning to look into wireless for in house use. I am looking for a simple recommendation or direction I should start looking. My primary need is for a Software Training room with 14 node than constantly need to be broken down and moved. I...

I'm in the process of configuring an Aironet 1200 with IOS 12.2(13)JA1. LEAP & MAC Authen are enabled along with dynamic WEP keys. Let's say I rotate WEP keys at 10 min intervals. This should generate a Passed Authentication message of " Re-Key OK" o...

Hi all,Do you find out the complete list of error and log which could happen on these device running IOS?Does it exist a document like "Sytem MessageGuide" as we have with IOS on router?Thanks in advance for your answer,Regards, Frédéric

Hi,I've setup EAP authentication (PEAP) to authenticate WLAN client on an AP. The AP is connected to a switch where the port is not configured for 802.1X. On this switched port I enabled, in multi-host, 802.1X to authenticate also the AP as a client,...

I was browsing though the Cisco site and found out the the end of sale for the Cisco 350 Bridge Series. We employ Cisco 350 Series Bridge 12.00T on all our wireless sites for interbuilding connectivity.Can somebody recommend me the latest Ciso Bridge...

We've got about 120 aironet 1100s in use. They're all configured for the use with leap "authentication network-eap eap_methods"Since we're using all aironet 352 Pcmcia cards we don't have any problems.Now we are in the negotiation phase for new handh...

The scenario is a WISP. I am using Upgraded 350 APs and 1230s.I am successfully able to reserve and allocate IP addresses to the BVI interface using MAC addresses as a parameter.However does anyone know how I can allocate the Default Gateway, Hostnam...

Customer has 3 AP1200's with Local List MAC addr.authentication. The problem is that each MAC addr has to be manually added on every AP. Can one combine the Local Radius Server functionality from 1 AP with MAC addr authentication such that the MAC ad...

I have a problem with some of my clients. They have static IP's but attach to the AP350 with address 0.0.0.0 and with : "OK, WEP, IP Forwarding Agent, BOOTP/DHCP Client, IP Virtual Router." in the Status cell.What would cause this?Thanks.

Hello,I have deployed a Cisco 1200 with both IOS and VxWorks. I have a distributed antenna scenario. I have one cable on the right hand connector that goes out about 100 feet goes through a three way splitter and then goes another 35 feet in three se...

From the information in Location manager, it appears that the WLSE 2.5 assumes that all my access points are using the Omnidirectional (rubber duck!) antenna, and thus the radio coverage is more rounded.We use Patch antenna to direct the radio covera...

Is there anywhere I can download the template for the G ap's for the WLSE...I am in the process of converting our existing wireless infrastructure to G...I have tried to import the config from one of the 1200's but it only shows the config in the "cu...

I am trying to get "ip http authentication aaa "to a 350/1200 ios wireless access point to work using RADIUS (using ACS 3.2 and Cisco IOS/PIX RADIUS Attributes). I can get the 350 vxworks to work by adding"aironet:admin-capability=write+snmp+ident+fi...

We got our first CB21AG cards last week, and I've been playing with it to get it to work with the APs and ACS server that we have setup. I've installed the software and configured it exactly as the LEAP software for the older A cards is setup but the...