Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
I recently added 6 remote 350 brides to an existing network that has a 340 as the root. The network is setup as a point to multi-point, with the 340 as root, 6 350's and 1 340 as non-root w/o clients.I have noticed that it takes the 350 alot longer t...
HelloI have a little question about different VLAN's on a AP 1230 and the Trunk between the AP and a switch.The Situation is, tha we have the VLAN's 1 ( native ), 22, 153 ( voice ) and 192. All VLAN's exists in the wired LAN. The AP is in the IP Rang...
Does anybody know if the universal power adapter is plenum rated for a 350 bridge? I know the bridge is plenum rated but the docs show nothing for the power supply.Seth
PEAP + Dell WNics + ACS + NDS/eDir + Novell Cert Server -- Can it work?I am supposed to do a global WLAN rollout next year and would like to use PEAP, but we are a Novell shop and use the Novell Client. Should I attempt to go down this road, or take ...
I am trying to authenticate my clients with a radius server. it works very well with ACS for windows. I am using LEAP. ¿What Do I need into RSA/ACE to work?Thanks
Hello,I ve been trying to establish PEAP authentication using following configuration : Windows XP SP1 EAP suplicant (using different client cards - Cisco, 3COM, D-Link), Cisco 1100 AP (12.2(8)JA ) and MS Windows 2000 SP3 IAS radius server with 802.1...
Hi,I want to use 802.1X as authentication framework on both wired and wireless network...but use one Authentication method for both nets...Does ACS3.2 support Cisco PEAP only with EAP-GTC or could I use all the EAP's flavour like MD5, MS-CHAPV2 ???Is...
The question I have today concerns using 2 antennas with a Cisco 1200. We have a customer that was using Proxim MP11s along with Proxim 600s to provide Internet in an apartment complex with 560 units and 8 APs. They were getting poor performance so t...
Think i am right in saying cisco don't currently ship an 802.11g based wireless bridge.Anyone know of any plans of ciscos for the introduction of such a device (lots of other manufacturers do them). i have a customer who needs>6M, doesn't want to use...
I have a root AP with 6 dbi wall mount patch anntena , I still have uncovered area and I can only use repeater , this is an outdoor area (planes RAMP)that looks like a soccer field with 280 m distance from the root AP to the edge . Can I use repeater...
Hi, While a wired backbone might be a better solution, due to limitations I am looking at setting up 350's as repeaters with a maximum of 3 links. Does anyone have any experience in how well, if at all, a 350 will operate as a repeater through the fl...
I have an access point, 350 w/ Firmware 12.02T1. I am having problems with it rebooting several times a day due to an error saying the memory is full. The error in syslog is FATAL): Rebooting System due to Out Of Memory Anyone know what is going on w...
I would like to do an omni coverage wireless connection between the radius of 1KM.I'm planning to use Cisco aironet bridge with an omni directional AIR-ANT24210.I will set the aironet bridge to act as an A.P so my client notebook will get the wireles...
The management VLAN for our APs is 196. Is there anything wrong with setting up the BVI interface as follows:?interface BVI1 no ip address no ip route-cache!interface BVI196 ip address 130.39.196.48 255.255.252.0 no ip route-cache!ip default-gateway ...
Does anyone know if there is any bulk install method for Aironet Wireless Client? --for example, with VPN client, we can preconfigure the .ini and .pcf files and distribute it with the ext file -- Is there anything like that can be done with the Airo...
