What is purpose of ALC configured at wlc? The purpose is for security via blocking unusful traffice. so There are three kinds of ACL for it. first is to allow dhcp, and second is to allow dns traffice and third is to allow icmp. and then block all o...
Hi everyone,I have an issue at an overseas branch office where we are advertising an open SSID. The problem is that users do not see the SSID which we advertise but see "[SSID name] 2" advertised instead. When they connect to this duplicate SSID they...
HI everyone. I just noticed this. I have different series of AP , 1142 , 1252 , 3500 , 3700. it is happening on any series. if I set the duplex and speed to Auto some of my AP are connecting with 100mb not 1Gps. if I set duplex to full and speed to 1...
Hi Guys,My company is looking at installing the Cisco Wireless LAN Controller software for managing our Access Points and promoting BYOD (Bring your own device).We currently operate 6 sites throughout the country all connected by WAN. We currently ha...
I am fairly new to the Meraki environment so please excuse my lack of knowledge with the dashboard and equipment.So we have a few MR46's that are registered in the dashboard but have not been connected to the Cisco network yet.There is 1 MR46 that ha...
I've got a 2504 WLC with AIR-CAP2702I-A-K9 APs. Software on the WLC is 8.0.132.0 Issue is with a single WLAN when getting IP addresses via DHCP. These APs are in local mode as well, so CAPWAP tunnel is built to the WLC.This SSID is in the 10.2.1.x ne...
We are in a bind and need to implement a controller using 8.10 and being deploying 9120APs. The main controller is stuck on 8.5 due the number of older 3502 and 3602 APs. I've always thought the version of AireIOS on the controllers had to be consi...
Hi In WLC, from WLANs -----> Advanced -----> AP group -----> we can see blue triangle on the right side. When moving mouse on it, it can show several choices. One of them is NAC Enable. Please see the below screenshot. NAC is part of ISE. We can thin...
Hello everyone.I have the next problem, Attach an evidence log:###########################################################Octeon cust_kukrip2(ram)# fatload usb 0 0x20000000 AIR-CT3504-K9-8-5-131-0.aes** Bad device usb 0 **Octeon cust_kukrip2(ram)# st...
Bought a new Cisco 3504 WLC. I've connected a USB cable to the console port and accessed the console via the terminal on my Mac:screen /dev/tty.usbmodem1461 9600 I then restart the 3504 and all I get in the terminal is "Cisco bootloader . . ." - I t...
Hi friends,We recently purchased a 9800 controller and 20 AP model 9130AXE-E.I set the controller but the AP does not transmit a 5G frequency. When I check the AP status I see that theregulatory domain is -E.I set the country code to my country is...
WLC5520 - 8.5.182.0 Under Wireless - Access Points- Radios 802.11b/g/n able to see details and interferers in the details part for all my 2600,2700,3700 but not 2800. Just shows very basic detail, no persistent devicesUnder Wireless - Access Points- ...
I have a brand new Cisco C9800-L-C-K9 , when plugged on power I can only hear the fan running but no lamp is ON , I can not access the device via console , please help
Hello Team,my wireless user authentication happens on Cisco ISE but here client is recommending one setup over the ISE where Radisu and TACACS can get only Level 5. Can any one help me how to do this for Both RADIUS and TACACS ThanksManish Jain
Hello Team, I wanted to know that if there is no firewall for guest traffic but still i have one foreign WLC and Anchor WLC then how to isolate traffic for Guest-users using our core network. Please let me know how many options are there for this ki...
