Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
I encountered an issue with a working mobility tunnel went down for unknown reason and could not get it back up. The foreign WLC which is 9800 L F with 17.12.6a code version and an anchor WLC 9880 running 17.12.4 code version sitting behind a Palo Al...
Hi Guys,I am just wondering if it is possible to integrate the Alerts under Insight tabs to ServiceNow? I tried adding my Webhook link in "Insights > Alerts > Alerts Management > Settings" I also tried adding the Per-Alert webhook under "Insights > A...
Hi ,We have a fairly large Meraki setup. Approx 5500 APs scatered on 800 sites. Some sites are super small , and some have more than 40-50 APs. https://www.ciscolive.com/c/dam/r/ciscolive/apjc/docs/2025/pdf/BRKEWN-2046.pdfThis document seems to sugge...
I was just asked to if I can setup a new "guest" Wi-Fi SSID *and* attach a Guest *wired* LAN connection. A 3rd party company is coming in early next year and is bringing in devices that need Wired and Wireless connections. CIO does not want them on ...
The Why: Now that wireless itself if a platform, we are working to get a safety locationing application using the Cisco APs to Blutooth beacon. What We Need: To export all our maps with the location of the APs.I will start looking around in the APIs,...
we connect the uplink for standby WLC (CW9800M) with core switch and port down but i receive RX power for this portif the port will be up after switchover ?can you help me ?
Hello, I need to replace the current 3504 controller with another one. I’m having issues doing the backup through the GUI because the controller reloads each time.Is it possible to do it through the CLI?For example: run show running-config, copy the ...
Hey,I'm trying to connect my MacBook to a Chromecast so I can stream video, but I can't figure out the setup. Can someone give me step-by-step instructions or tell me what software I need?Also, if you ran into problems before, what troubleshooting st...
Good morning all,We have an outdoor environment with MR86's and we are seeing an issue where the AP's will not increase their transmit power past 11dBm regardless of the target power set or manual configuration on the 5ghz band. This is causing a ter...
Hello Meraki Community,We're aware of a developing issue affecting CW9172I and CW9172H wireless access points, which are currently unable to upgrade or downgrade to any version of the MR 31 firmware train due to how images are downloaded from the bac...
Hello CISCO Community,I wish I could get some support or ideas on how to convert our AIR-AP2802I-E-K9 to Mobility Express.So we're moving into a new office and the previous tenants left 2 units of the AIR-AP2802I-E-K9.I understand these are in CAPWAP...
Network scenario: WLC 9800 (192.168.110.9) is connected to Core Switch (192.168.110.1). Then From Core Switch > PoE Switch > APs are Connected. but main problem is I couldn't connect to WLC using SSH from any Vlan or SSID and also not getting GUI fro...
Olá a todos da Comunidade Cisco,Gostaria de solicitar suporte para configurar um Access Point que recebemos como doação: Cisco AIR-CAP3602I-T-K9 (Domínio Regulatório T). Problema Principal: Não estamos conseguindo realizar a configuração inicial do e...
anyone use letsencrypt certificate for WLC 9800-CL?I managed to import the letsencrypt cert using CLI, but from CSR and step by step, but after 3 month, what can do? redo all the step again? There is GUI to import, but does it really work?
Greetings,Just want to check if anyone has experience integrating Meraki wireless to Aruba Clearpass radius. This is a new setup, we use SSID with a radius setting and with splash page wherein this will be redirected to Clearpass to authenticate the ...
