Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Hello Professionals,I have currently using WLC2504 with 40 access points and I'm about to replace new WLC (WLC9800).I finished interface/WLANs/AAA (for authorized AP can join only) configuration so I would like to connect new WLC to my network.Howeve...
I reviewed the RF Performance table for the MR86 and noticed that the Total TX Power (conducted) decreases as the MCS rate increase:https://documentation.meraki.com/MR/MR_Overview_and_Specifications/MR86_Datasheet1. Why does the Total TX Power (condu...
Hello everyone,I have a problem with AIR-CAP2702I-E-K9 series of Cisco’s Access Points. 2 out of 15 APs won't associate with the WLC 8540 even though they have exactly the same configuration. I'm using only one IP address to test the APs. The two APs...
Hello, ive brought up the new Catalyst 9115axi embedded wireless controller and have it configured, as well as the software download portion in the ewc. Using tftp pointing to local pc to grab images as I add additonal subordinate ap's. I tested a co...
Hi all, I am from india.I am facing issue in AP 9166I-ROW-6E model ap not joining to C9800 WLC (Country Code - IN) I want to know that is this AP supported in India ? If not should i change the WLC country code to US. it is fine with Cisco regulat...
WGB will get stuck to an AP and then will have to be kicked off of the controller and it joins back again ; no issues. this happens with most Cisco WGBs in a manufacturing environment like ours.Please any suggestions, list of steps that can be tried ...
we have an existing 9115 embedded controller and we want to add one1832i acess point and join it to the embedded controller. We are having an error with"Discarding msg CAPWAP_WTP_EVENT_REQUEST(type 9) in CAPWAP state: Image Data(10)". The 1832 ap is ...
i am using WLC5520 ,unfortunatily its not taking cisco image booting . whats the issue .i take the SD flash disk inside the controlled and put it my lap top it was empty . is that reason its not taking boot? wherw WLC image stored in 5520?how can i ...
Hopefully I this is an easy one and I am just not looking in the right place because it's Friday and I am hanging out for a beer..I am trying to see the live stats for how many clients are connected to an SSID, I am sure I've done this in the past bu...
Hi Team, There is a new firmware released MR 29.6.1 and noticed something scary"In high capacity wireless networks APs may experience instability when the “Client Balancing” or "Band Steering".1. Is it something we have to worry about before upgradi...
I have configured WebAuth for Guest SSID, But issue is after put credential its showing Authentication failed. I follow cisco document as well YouTube tutorial but still same
Hi all,I found this document that claims APs can send SNMP traps whenever an antenna gets degraded.https://www.cisco.com/c/en/us/td/docs/wireless/controller/9800/17-5/config-guide/b_wl_17_5_cg/m_antenna-disconnection-detection.htmlI wonder if this ho...
Resolved! AIR-AP1562E WGB Mode
Hello, my question is, why there are only outdated or wrong documentations existing regarding APs in WGB mode. Having a WGB, AIR-AP1562, which shows following log entrys at every roam event: Jul 27 12:24:05 kernel: [*07/27/2023 12:24:05.8517] DOT11_U...
Resolved! MR86 Antenna Frequencies
Do all 4 of the MR86 antennas transmit all supported bands of the MR86? or are some dedicated to 2.4GHz and others to 5GHz?
Resolved! MR86 antenna placement
Are the benefits of 4x4 MIMO deminished if I extend the omni antennas away from the base unit?If 4x4 MIMO is deminished, do I deminish max throughput rate?
