Any suggestions for how to automate a monthly change to the PSK for the guest wireless ssid. Attempts to connect to the wireless controllers in Powershell with poshssh and plink run into issues trying to authenticate. The first prompt at login being...
Forum Posts
In Cisco 9800 Wlc how can we check for the clients with highest data usage same as we have on AIR OS controller. We are currently running on 17.3.3 ver.
Hello There, I want to connect MR Wireless AP Via HPE Procurve SwitchMeraki MS390 --> HPE 2520 --> MR36Meraki MS390 Port setting: "Trunk" ↓HPE ProCurve 2520-8G PoEUpstream/Downstteam Both Port setting: VLAN "Tagged" (same VLAN as Meraki MS) ↓Meraki M...
[Bengaluru , Amsterdam , Gibraltar , Cupertino]What does the image name mean?
Hello, We have a request for a client PC to auto connect to one SSID always and prioritze it to auto connect to that SSID always before user logon, is there an xml profile editor to fulfill this request Thanks in advance
Resolved! gtk per vlan for same ssid
I want to know if you support setting up at GTK pr VLAN for users that are on the same SSID but gets assigned to different VLANS.The goal is for broadcast and multicast to be limited per vlan instead of pr ssid. Aruba Instant On does not have this fe...
Resolved! syslog: disassociation reason
Hi,When I look at the wireless syslog, it looks several types of reasons exist for the disassociation event. See below examples. Can you give a short description about each number of the reasons ? At least, I got 2, 3, 6, 8, 15, 23, and 34.2023-06-26...
Hi Guys, I have an AIR-AP1562I access point which was used in a 9800 WLC, so the software on this AP now is Capwap Catalyst software version 17.6.4.56. I would like to convert this AP back to AireOS software, I would like to use it as Mobility Expres...
Hi Guys, I have an AP in a production network that can't connect to any WLC after deployment. Image download from controller was successfull, but it got "Max retransmission count exceeded, going back to DISCOVER mode." error message during CAPWAP Con...
Resolved! Preauth ACL in WLC 9800 Behaviour
Hello everyone,I need to configure a preauth ACL for webauth " CWA ". In fact, i am migrating from a WLC 2500 to WLC 9800, and the confusion is in the permit/deny enries, on the 2500, they say :"this ACL is referenced in the access-accept of the ISE ...
Hi,In the below design guide explains only layer 2 connectivity ( wlc to the upstream switch ) https://www.cisco.com/c/en/us/td/docs/solutions/CVD/Campus/cisco-campus-lan-wlan-design-guide.htmlPlease guide layer 3 implementation for the same Th...
Hello! I have a building where i can't run ethernet everywhere. Now i am looking into mesh. I have built a little test with two 2702I's (bridge mode) and when they are in the same room i get close to 200mbps, but when i go outside that room it drops ...
Hi, I'm a beginner engineer. I'm trying to join a new AP to WLC since the existing AP is defective at the place where I'm currently in charge of maintenance. In this way, an image download fail appears, starting an infinite reboot. According to what...
Recently I have been having issues with a Meraki mac-based access control SSID. The issue occurs when an Apple or Android device will go to sleep, and when the device is woken back up, the SSID has disappeared from the device. You can re-enter the ne...
Resolved! Access Point MR-44
Good morning, to connect 6 MR44 Access Points without the need for PoE power, what MS Switch could you propose?
