We have a spare wlc9800-40 we are trying to use but it keeps rebooting over and over with below. I've tried to boot from various versions and still get the error output below. It seems to think there is an HA pair that its not seeing so it reboots...
Forum Posts
I have an issue regarding on the Lobby Ambassador Admin of WLC9800 where the credential is configured from Cisco ISE TACACS+ Initially, it can log on successfully using the username and password configured from Cisco ISE TACACS+, however, it immediat...
Resolved! cisco 5220 vlan port 1 port 2
Hello,I have two switches 9400 redundancy SSO , I create SSID with different VLAN only one work VLAN 145 I can ping the gateway from WLC but for the other impossible to ping other gateway!!! , I allow all vlans in two ports same , can you please hel...
Resolved! My WAP does not exist?
Hello,I have a number of Cisco 3502i WAP's and that product has been completely removed from the Cisco website. I know they are end of life, etc. but surely the data should be preserved for reference.Here is the pertinent informationAPMACAddress#sh v...
Hi Team,I would like to confirm if this Access Point Image Version Number 17.12.3.31 is compatible with 17.9.4a cupertinoDevice ID: AP505C.88D5.872C Platform: cisco C9120AXI-A, Capabilities: Router Trans-Bridge Interface: GigabitEthernet1/0/38, Port ...
I have installed a 9130 EWC and it is running version 17.9.6 successfully.I also have a 3702 running in lightweight mode with LWAPP image version 17.9.6.40 to match. However it will not join the EWC controller.On the 3702 side I see:*Feb 1 04:41:49.0...
Resolved! Cisco 9800 VRF 17.13.x question
Hi all,Looking to design/deploy a couple IoT enterprise wireless networks. One of the WLAN networks will have access to the Internet only. The second WLAN will have access to the Internet as well as the internal (trusted) network. Could I leverage...
Resolved! Cisco 9115-AXE web Gui access issue
I'm working on configuring the Cisco AP 9115-axe as embedded wireless controller. So far I've changed the AP to EWC mode and configured the hostname, IP and route. AP is connected to Cisco 9200 switch running version 17.9.4a, EWC is running version 1...
Resolved! How can I see an AP neighbors
Hi buddies, I've deployed a vwlc 8.0.120 and some Cisco 2700 series APs. I want to know is there any way to find out each AP is neighbor with which APs through vWLC? BR, Majid.
hello, some of my wireless client have intermittent connection issue. When i try ping from my laptop to the my android phone i can see many request time out. The client have good rssi if I check in the WLC and connect to AC radio Try to debug the ...
I have a Guest WLAN created on my WLC. However when I connect to the wifi network the following is shown:(Cisco Controller) >show certificate webadminShow Web Admin!WebAdmin Device Certificate details:Subject Name :C=US, O=Cisco Systems Inc., OU=Devi...
After regenerating the certificate on the ISE, I receive a certificate trust message on every connection. I exported the certificate and installed it directly on one of the test PCs, but the message still appears on every connection. Can someone ...
Resolved! flex connect ipoverlay cisco 9800 wlc
Hello Team,what is the option name ip overlay in flex profile of catalyst 9800 wlc?will it cause any impact in the network. Regards,Anjana
Hi Guys,I didn't find a solution for my bridge system's bug.There is a small mesh system with 1 RAP and 4 MAP.All of them are C9124AXE APs with 6 antennas.The WLC is a C9800-40-K9, ver: 17.12.4Almost everything is working except the slot 2 radio sett...
Hello Guys,We have some old APs 1602i devices which are giving very strange issues. We had many of them in boxes sitting in the store for a very long time. But when we tried to check a few found interesting fact that those APs stuck at boot Loading "...
