Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
All,what happens when an IDS Signature Attack is detected? What is the response of the Wireless Controller? Does this lock out all users on that AP for a time period or just that individual user for a period of time? thanks
Hello,I am trying to get a AIR-AP1542I-E-K9 working with a Catalyst 9800-L controller. I have no previous experience with a wireless controller, only having worked with Cisco routers and switches before. I cannot get the ap to even pop up on the GUI ...
I had to recover a WLC after the password was lost. After successfully doing so using ROMMON, I somehow changed up something in the configuration during the webui configuration wizard to the point where the APs are no longer able to reach the WLC. I ...
Attempting to wirelessly bridge two buildings using two 1572-EAC APs and a 9800-L-C. Wired clients in the second building must be able to access LAN in the first building.So far have the 1572s registered as Mesh APs to the controller. Both APs are ...
Hello friends, you are projecting an implementation of AP in monitor mode, dedicated to WIPS, I just passed the wireless design specialist exam, but there was no information on the criteria of where to position the APs.My question is where to put the...
Resolved! AP2802I-E-K9 - WLC+AP - Green+Blue+Red
HelloOk today was deliverd the original Air-pwrinj6 PowerSupply, What a joy!Reset this AP and Configure anything, for me ready for use. ->Image 8.10.151.0 But LED Flash Green+Blue+Red, please this AP "AP2802I-E-K9" can run as WLC+AP together?i read i...
Resolved! AP power managment
HI All I have 13 x C9120AXI- aps plugged into a 2960 switch (POE). I am up to maximum watts capacity. I would like to get one more AP onboarded. Is there a way of tweaking the APs power on the following WLC please ? Cisco Catalyst 9800-L Wireless...
Добрый день!Настраиваю WLC 3504. Через сервис порт подключился для управления. Две АП подключил к 3 и 4 порту чтобы работали через POE. Настроил management интерфейс. Настроил внутренний DHCP для АП.Настроил WLAN и интерфейс WiFi, через который клиен...
A couple weeks ago, it was been reported that some HP Laptops have been getting disconnected from wireless. The common complaint was that they needed to "disconnect" from WiFi and then "connect" to wifi again on the business SSID. I was able to obtai...
Hi there, once again hoping you're healthy. We have a WLAN with 6 APs model Catalyst 9130 working by Embedded Wireless Controller. The software version of this controller is 17.7.1. The problem is that every Access Point in the network is continuousl...
We have Two Cisco Catalyst 9800-40 Wireless Controller and version 17.3.3.Both WLC configured in HA mode and working fine. I want to connect the both WLC to Network by SP port so that I can access both WLC. It will be helpful during HA configuration....
I am running Cisco 5520 Wireless Controller.The AP model is AIR-AP1852I-Q-K9 , The IOS version is 8.8.130.0There are 2 SSIDs configuredSSID#1 : INTRA_WIFI - For Internal Wireless LAN network : Uses certificate authentication SSID#2 : GUESTWIFI - For ...
Hello, I am wondering if we can configure by using Meraki to control the end-user's wifi session. What I want to do is to assign 5Gb data quota to the end-user monthly, and if the user used up the all data assigned, Just disconnect them until the nex...
Hi,I have 2 SSIDs and have been asked to limit the bandwidth of Guest ssid.I check both SSIDs and both have QoS as shown below. Please see File 1.MY first question is which one of the QoS is it using right now as I think that is is not using any spec...
I need to update the image for the 9800 EWC running on some 9120 AXI's so that newly purchased 9105's can join the active controllers. The Software Management tool is requiring me to supply an AP image as well before I can click the "activate" button...
