Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Hi,We are (have to) deploying wired dot1x on our network. We are using Cisco APs (2700, 2800, 9120 models), some locations in local switching mode, some locations in central switching mode. What is the recommended configuration switch LAN port config...
I know it's not very scalable but for a temporary solution I've been asked if there's a limit to the number of clients that can connect to an SSID with one set of credentials in the "User management portal".Can't see anything documented.
Hi all,I have an iPad here that regularly loses connection.Catalyst 9800-CL 17.3.3FT-802.11x onOther Apple devices are behaving normally. The first strange thing is that every few minutes there is an "Association received" and after a few more minute...
Cisco 5520 WLC Version 8.5.151ISE 2.7Cisco AnyConnect 4.10Cisco 3702Is it expected behavior for a authenticated and connected client to be disconnected when the flexconnect AP goes into standalone mode? I was under the impression that currently authe...
Good Morning, Meraki wizards.I have a project to cover an exterior farm of about 4.5 acres, that needs complete coverage. if each AP is wired I was considering 4 one on each corner facing inwards, if not wired I would have 5 main one would be wired i...
When doing Stick Survey I use a 9120 with EWC or a 2802 with MobilityExpress, mount it on a camera stand and use Ekahau with sidekick to measure signal strength and other various metrics. But how does my settings in the AP really reflect how RRM will...
Sinds yesterday I have a cisco aironet 1815i. I did start configuring with the cisco mobility express for phones. After I made a configuration I would change it. Only I can't change any configuration. So, I decided to factory reset the AP. Only if I ...
Hello,I have 2 C9800-CL WLCs Version 17.3.5b running on Hyperv, they are forming a working HA/SSO cluster.Last week, we had to patch the host where the 2 controllers were located, so we had to migrate the 2 VMs to another hosts, and the cluster has b...
Hi. I have a 9120AXI ap running version 17.3.6.76. I have a 10 ap's in production that I runs 17.6.1.13 code. I want this new ap to join the EWC controller instead of upgrading all 10 ap's in production to newest release for now. If that is possible....
Resolved! Azure SSO login fails after MFA
HelloI've followed these two articles to set up SSO logins:https://documentation.meraki.com/General_Administration/Managing_Dashboard_Access/Configuring_SAML_SSO_with_Azure_ADTutorial: Azure Active Directory single sign-on (SSO) integration with Mera...
Hello Experts, We are a small org with mix of fifty Aironet 3702s and 3802s access points managed by 5508 dual controller in HA setup. This summer we are planning to upgrade it with Embedded Wireless Controller (EWC) running on Catalyst 9130AX acce...
Resolved! QoS for "Fuze" voip and conferencing
Hello,I am trying to add DSCP tagging on our MR36's for our VOIP and video conferencing software called "Fuze" (aka 8x8).I have this from their documentation - Would adding a rule of "all voip and video conferencing" (there isn't a specific definitio...
My wireless clients can reach internet but can’t be reached from internal network. Routing is in place as wlc SVI in same subnet can be reached but clients can’t be reached internally even though they are getting valid DHCP ip address/gateway/mask. I...
Resolved! C9130-Multi
Hello, This is a rather simple question. We purchased a few Cisco C9130AXI-B WAPs and in packet list it shows the following item: C9130-MULIT --- Minimum Quantity = 10 What does the "MULTI" refer to? Thanks in advance.
My environment :Foreign 9800 - Code version tested - 17.6.4 and 17.3.6Anchor 5508 - 8.8.130 and 8.5.XI am having issues while creating tunnel between 9800 ( foreign ) and 5508 ( Anchor ). WLC IPs can ping each other ( data path is up ) but control pa...
