My AP device has this problem of constantly booting up. Meraki Mode Selected ubi0: attaching mtd1ubi0: scanning is finishedubi0: attached mtd1 (name "mtd=0", size 242 MiB)ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 253952 bytesubi0: min./ma...
Forum Posts
I need to update the IOS version of the Catalyst 9800 L-C, at this moment it has this version: Cisco IOS XE Software, Version 17.06.05Cisco IOS Software Bengaluru, C9800 Software C9800_IOSXE-K9, Version 17.6.5, RELEASE SOFTWARE fc2. I need to install...
Hello!Tell me what the problem might be, there is a C9300-24UX-A switch, a "3504 Wireless controller" and a pair of "AIR-AP1832I-R-K9" are connected to it, and one AP is also connected directly to the controller via a PoE port.WLC3504 sees all access...
Hi all;Consider the following scenario:I want to configure Mobility Tunnel between these WLCs (both of them are 9800-CL with IOS-XE 17.12.4). As you can see below, both controllers can ping each other without any problem:Form the configuration point ...
Hi community,I'm trying to get an USC5310 working on a AP C3600 (AIR-CAP3602I-E-K9). I set up the AP C3600 as stand-alone using software AP3G2-K9W7-M version 15.2(4)JA1.Unfortunately, when booting it reports "Unknown Expansion Detected, please config...
Hi, has anyone had the chance to play with "AI-Enhanced RRM" in Cisco Catalyst Center ? What has been your experience ? We have quite a few RF profiles and wonder if the cloud-based RRM really does a good job so we can lean back and stop using our ow...
Resolved! Recovery image for Aironet 1815i
Hello: We want to add some 1815i APs to an old WLC deployment. We're only able to find new 1815i autonomous (K9) but we need lightweight ones 1815i (K9C). We know that we can use the recovery image for convert autonomous to capwap, but in the drivers...
Hello, I can't find the Power adaptor AIR-PWRADPT-RGD2 in the CCW, any update and which part number to use for access point C9124AXE-ROW
I have accidently removed partition 1 & 2 during the uboot.Now the AP boot loop with below.____ _/ ___|(_) ___ ___ ___| | | |/ __| / __|/ _ \| |___ | |\__ \| (__| (_) |\____||_||___/ \___|\___/_ _ ____ _| | | | | __ ) ___ ___ | |_| | | |___| _ \ / _ ...
I'm using a few Cisco Aironet 1142 ap's in my house configured with autonomous images.The firmware version I have is c1140-k9w7-xx.153-3.JD17.The problem I am running into is there is nothing at all under Network Interfaces on 3 of these ap's.One sho...
In a Cisco Catalyst Controller 9800 SSO deployment, will failover occur if the interface or port-channel of the active WLC is physically shut down?
Hello I am experiencing an unexpected behavior on the WLC (C9800-CL). After adding a new APs (CW9164I-E), it displayed the following error message: "Regulatory domain check failed" (Figure 1). Upon reviewing the logs (Figure 2), I noticed that the ...
Hello,AP for branch office registered to the WLC in Main Office, and the AP using flex connect mode.If we see in below picture, VLAN 250, 118, 124, 117, 131 is not exist in the Main Office, only VLAN management 303 exist in the main office.With this ...
How Data traffic will be done between AP and Controller ? Is it go through CAPWAP, I believe CAPWAP used to both control plane and data plane ?
Resolved! EWC on 9115 17.12.03 telnet to APs
Hello colleagues,I'm running Embedded Wireless Controller 17.12.03 on C9115AXI and having issues with this config:ap profile default-ap-profile description "default ap profile" mgmtuser username admin password 0 Admin,12345 secret 0 Admin,12345 ntp i...
