Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Hi,I don't have L2 adjacency between core because the connection between core is layer 3 . Since there is no L2 adjacency between core , I have to create SVI'S only on one core .So the other option is to create svi's on wlc. As per cisco it is n...
I do have issues in WLC after moving from traditinal 6500 switch to ACI leaf . issue 1) Getting packet drops while pinging the virtual ip address and no drops in the physical IP address . Issue 2) The MAC address of the WLC is reported in EndPoint da...
Hi AllI have been trying to deploy a wireless solution but been stuck with appears to be an authentication failure with the Radius Server . The device is an Intune laptop attempting to connect to a Meraki managed SSID but every attempt has bee...
Hi AllI have been trying to deploy a wireless solution but been stuck with appears to be an authentication failure with the Radius Server ( ISE) . The set up consist of an Intune laptop attempting to connect to a Meraki managed SSID . I m using Merak...
CVE-2004-0230 [TCP Sequence Number Approximation Based Denial of Serv]The above vulnerability exists on a couple of Cisco wireless controllers and Cisco IOS switch. how to resolve this issue Kindly help me on it.
Regarding to the Pass-through Rj45 port, as I've read it acts as another wall jack that works even if the AP goes down. My Question: Is the Pass-Through port -on this AP model- transmit power to the connected device or not?
I have a cisco 2702i access point autonomous and connected a KEF LSX audio system to it. With my iPhone I have a WiFi connection to the cisco, but I don't see the KEF LSX listed in airplay. Anyone have an idea how I can solve this?
Hi i have routed access layer design as im running L3 to the access and OSPF as IGP ( Core - Distribution - Access ) thw WLC 3504 connected to the Core the the APs 1800 connected to the Access Sw each with different subnetsi could register the APs to...
How do i set a night shutoff timer for the public wifi
WLC9800... I have a SSID with CWA with ISE working just fine and another SSID using MAB. Customer wanted to collapse these SSIDs into a single one and use MAB first, if that fails then redirect to the CWA portal. Since the authentication piece is ...
Resolved! C9120AXE ssh, mgmt user connfiguration
Hi there,can anybody tell me how to configure ssh and the mgmt user on C9120 access point via cli?Thanks in advance for the assistance.
Hi, I have two HA C9800L-C controllers, one in LAN, one in DMZ. I have 9105 Teleworker AP used at remote employee house tunneling back to DMZ (using this guide: https://www.cisco.com/c/dam/en/us/td/docs/wireless/controller/9800/17-3/deployment-guide...
Resolved! Cisco 9120AXI reset in ME environment
I need to install EWC on a 9120AXI. The only way I have to power on the switch is via POE, and the AP will then find a 2802 with mobility express on it and register itself to that controller.The problem I have is gaining SSH or console access to the ...
Resolved! Radius and Tacacs at c9800
Hello, I have a question on below document/link, which is talking about setup RADIUS and TACACS+ at wlc 9800. Both Radius and Tacacs has very similar configuration at c9800. The question is why it use both Radius and Tacacs at C9800 at the same time,...
I am currently getting one-way audio (inbound) with a Spectralink 8440. Outbound is not working. Both QoS ingress / egress is set to platinum/platinum-up. I validated the client has this in their QoS.I try in my lab over a wireless Meraki network and...
