Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Dear all,My question is maybe a little bit newbie, but I would like to turn on Meraki roaming. In our office, we have many devices which support this feature BUT few devices which not...and I am not sure if the Meraki roaming will have a negative eff...
Resolved! Power Consumption of WLC 5520
Hi All , I need to find information about Power Consumption of WLC 5520 but I not see the information. Please help me .
Resolved! Issues with 8.10.181.0 and 3802s
Hi All-I just upgraded my 5520s to 8.10.181.0 in anticipation of deploying some new APs. 8.10.181.0 appears to be the only version that supports the 9120. It did no go well!We have pairs of controllers. I upgraded one to 8.10.181.0 and left one at...
Hello,I am a Junior - Intermediate level Network engineer.I am currently trying to configure our 9800 WLC management Ethernet ports purely for SSH purposes. We have 2 WLC 9800-40 running HA.I am looking for guidance or ideas on how to configure the p...
I'm having a rough time getting my new CBW240AC set up. I can do the zero-day configuration just fine, and after the automatic reboot I have wireless network access and can manage the wireless network. However, when I power off the access point and...
Hi, we are fairly new started with DNA Center and have been using Prime Infrastructure in parallel. What we see in DNA Center version 2.3.3.6 on 5520 WLC using 8.10.171 with 9120 APs that clients show broadcast rekey failed, we are using a WPA2 PSK b...
HI,We have several (12 to be exact) MR42 devices. In specs it is stated that those support BLE beaconing and BLE scanning.Scanning and Beaconing enabled via meraki cloud dashboard (IoT Radio Settings) , but no sensors with BLE enabled (non cisco mad...
Resolved! 802.11b Global clients threshold
Hi In mobility express GUI in RF profiles "Maximum clients per radio" limit is set to 200but in cli it is showing below.(Cisco Controller) >show advanced 802.11b profile globalDefault 802.11b AP performance profiles802.11b Global Interference thresho...
Hi All, There's an issue with AIR-AP1832I-D-K9 model ap not connecting to the WLC. When the AP connects to the WLC it goes through the discovery process 1st and joins then immediately shows DTLS teardown. In the same WLC AIR-AP1832I-E-K9, AIR-AP1832I...
Is it possible to have multiple primary 9800 WLCs configured to fail over to the same shared HA 9800?
Have tons of 9120's on the 8540 but the 9130 AP doesn't make it past the Discovery. I haven't gotten a hit yet on a search.[*10/20/2022 17:55:58.7157][*10/20/2022 17:55:58.7157] CAPWAP State: Discovery[*10/20/2022 17:55:58.7164] Discovery failed 7 ti...
I have 2 x 1gbps upstream LAG to Provider and it is heavily utilising the following on the ports:Port 1 - 100% with dropped packetsPort 2 - 2% UtilisationCisco's default hash algorithm for Port-Channels appears to be IP based and therefore will utili...
Hi, Is there any way, using the Catalyst 9800 WLC's to configure a critical access policy to enable clients that authenticate with 802.1X to access the network when the RADIUS server is down? On the wired, we can select this to place users in a certa...
Resolved! Content Filtering for Guest SSID
When configuring a Guest SSID on an MR using the Meraki AP assigned (NAT mode) option, under the firewall settings, there are options to block certain types of traffic like peer-to-peer or gaming, but there isn't anything for adult content, gambling,...
Brought some used APs from another location AIR CAP1602I-A-K9 but having trouble joining it with 5508 WLC Software version 8.5.171.0 Recovery Image Version 7.6.95.16. The AP is not connecting automatically and only LED red blinking in the AP. Alread...
