Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
Hello!We've a central WLC5508 with AP2801.There a several remote sites with APs in Flexconnect mode.Users just connecting to central wlc for authentication which is done on NPS.One remote site is permanently complaining, that they have troubles conne...
I have two WLAN. First WLAN1 has P2P action set to Drop. Second WLAN2 has P2P blocking disabled. Both WLAN are the same interface on the WLC. I would like to have a user on WLAN1 access a resource on WLAN2. Will Allow Private group work for just one ...
Hello, I am looking for some help regarding what I thought would be a simple WLAN setup. I must admit, Cisco network interfaces are not something I am familiar with at all. I have done a bit of poking around the Cisco community and it seems like ther...
Hi all, As stated in the title, I'm now investigating a situation where the client prefers the 2.4GHz band channel over the 5GHz band channel. After i'm seeing the on the transmit power configuration 2.4GHz power level 1/8 (22 dBm) 5GHz power lev...
Hi AP3800 in Flex mode is connected to wlc 5520. If we want to connect the AP to C9800, do we need to change Flex to local mode? Thank you
Hi,I have an AP-ME 3802 with firmware 8.3.150.0and 1 AP with firmware 8.3.111.0I have the file AIR-AP3800-K9-ME-8-3-150-0.taronce the .tar file has been downloaded to the AP with the commandarchive download-sw / reload tftp: // <<ip_tftp_server>> / <...
Hello, I setted up a new wifi network with 7 cisco ap 9115AX, and an embedded wireless controller. It seems to work correctly for laptop but some android devices cannot connect to the wifi. When I select the SSID on the Android phone I enter the secr...
Hi All,I have a WLC-9800 and AIR-AP-3802E-E-K9I configured two VLAN in WLC ,VLAN 100 For WLC Management and VLAN 200 for AP-Management.VLAN 100 IN Switch Interface Vlan 100 IP address 192.168.100.254 255.255.255.0Interface Vlan 200Ip address 192.168...
I just set up a guest wifi using Nat mode so I can use Meraki DHCP. When clients log into the guest wifi ssid after the splash page they get "net::ERR_TOO_MANY_REDIRECTS". Firewall settings are set to deny wireless clients from accessing the LAN.I ha...
I am currently using a Cisco 5508 WLC running software version 8.5.182.0. Can anyone tell me whether or not the Cisco Excess - AIR-AP1542I-E-K9 is compatible?
Hi, I can't solve this problem.Currently I configured multiple SSIDs didn't work.Hardware specification is below.WLC : C9800L-C-K9SW : Cisco CatalystAP : C9115AXE-K The symtoms are like these.1. Switches are can receive IP from DHCP pool.2. APs are c...
I have a question for you about a home-lab installation.does anyone have any experience with an MR18 outside? of course protected from the rain under a canopy, I would also insulate the connectors.According to the data sheet go only to 0 degrees, wha...
Hi community, I just purchased a Cisco CBW145AC Access Point and a CBW142ACM Mesh Extender.The access point is located in my living room, powered with a PoE injector (Cisco Business PoE Injector). The extender is on the second floor, basically just v...
Hi Team, Regarding to the document (section WPA/WPA2-EAP), why we still get a lot of frames in second times tls handshake, even through station already exchanged the certificate with the server earlier. Do we miss any seeting? Attached legacy roaming...
Hello Team, Recently I decided to use ISE for my guest access instead of using the wireless controller feature. Setting up a guest username and password to be distributed to our guest. I looked online for process and procedures and found many how to'...
