Hi Chrome can access WLC9800 without any issue, Firefox cannot. Please see the below. It used to access it. Dont know what happen. The below info is different with what we saw before. In the past, when visiting 9800, we got a warning saying accessing...
HiI'm unable to find details of the MA-ANT-21 hardware. Specifically, what kind of connector is required for an extended cable between an AP to the antenna.The documentation says that is an N-Type connector, but it doesn't say male or female plug.Wha...
Hi, I have a 2106 wireless lan controller and two 1142N-N-K9 LAPs. I am building a lab and am trying to get the APs to form a CAPWAP tunnel with the controller, however, this is not succeeding. So far the APs receive IP addresses from the pool config...
Clean Air is showing disable on Cisco 9130AXI AP when using it in a dual 5GHz on (SLOT ID 2). I was able to manually change it to enable but after sometime it will revert back to disable. I check the WLC and Cleanair is enable. This is only happening...
Hi We have Wireless and wired devices which need 802.1x authentication via ISE. We can see wireless authentication in ISE ( under Operations ----> Radius -----> Live logs) but cannot see wired devices authentication. Is this because wired device has ...
Hey Meraki Community,I have a feeling there is a simple explanation here but want to ask the gurus. Customer asks me what the 293 hidden SSIDs are showing up under the Rogue. I checked and indeed Meraki states these are recently seen on the LAN. Howe...
Hello,The power injector I am currently using (Model: DPSN-35FB A) has a blinking green LED for AP Power and a solid green LED for AC Power. I'm not sure if this is supposed to happen or if there is something wrong with the power injector. Appreciate...
Buena tarde a todos espero me puedan apoyar, tengo una duda al configurar un ssid en la WLC 8510 en el ancho de banda del Qos me marca que el rango limite es invalido si lo configuro con mas de 500 MB , me gustaria saber si es es posible configurar ...
Using the Intel AX201 and AireOS 8.10.162.11, our Desktop team are building a lot of laptops which can't connect to our WLAN. When doing a debug, I can see: *Dot1x_NW_MsgTask_4: May 16 14:20:05.208: [PA] a4:42:3b:7x:xx:xx Entering Backend Auth Succes...
hi,i'm posting screenshots of my wifi config and i'd like to know if there are other settings to improve my AP 2600i wireless connection.i have a fiber connection of 1 Gbps (with ethernet cable cat 7 25mt i see in ookla speed test 978mbps!) with the ...
Hello,My EA2700 router just functions just perfectly. The Guest Acces also, although very rarely used.Until today, when it appeared that the guest access dosn't function anymore.When starating to browse, the browser tells the user to register (with p...
Hi All, we have Merkai MR access points that are going into a repeater mode and causing loops in the network. these access points are power with a power injectors " not a POE from the switch " , when we upgrade the switches and reboot. MR will lose a...
Hi, I have little to no experience with cisco EWC.I want to create a 2 separate SSIDs which are Internal and Guest.I think in EWC, Guest settings is included. I want to use the same LAN subnet for both SSIDs. And I don't want the Guest Wifi to access...
can I have HA Between C9800-L-F & C9800-L-C ?
Hi there,We're currently testing out using JumpCloud LDAP with Meraki. We've got our SSID set up and we can authenticate and everything is great but we want to be able to do a bit more and are wondering the following.Is it possible to have Meraki see...
