Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
My customer has one WLC 5508 managing about 50 APs on 6 sites.They will move WLC to a different building at the same site but changing IP addressing for device access.I am looking for documentation providing best practices with procedure to follow w...
Good afternoon.I have a problem assigning a wIPS profile to a WLCs. The environment consist of MSE 8.0.150 , PI 3.7.0, Primary and Secondary WLCs 5520 8.10.151, APs 4800 in wIPS submode. We have all required licenses for MSE wIPS (ELM and MM both) , ...
It would be great if anyone explained why we get these errors on the Cisco Wireless controller. *dot1xMsgTask: May 31 00:04:14.261: %DOT1X-3-WPA_SEND_STATE_ERR: [PA]1x_kxsm.c:1718 Unable to send EAPOL-key msg - invalid WPA state (0) - client MAC*dot...
Hi everyone, what most likely could be a reason for WLC's syslog message like this: "Unable to send EAPOL-key msg - invalid WPA state (0) error" I have a SSID with radius (NPS) auth which has been working for about 2-3 years and accidentally st...
What is purpose of ALC configured at wlc? The purpose is for security via blocking unusful traffice. so There are three kinds of ACL for it. first is to allow dhcp, and second is to allow dns traffice and third is to allow icmp. and then block all o...
Hi everyone,I have an issue at an overseas branch office where we are advertising an open SSID. The problem is that users do not see the SSID which we advertise but see "[SSID name] 2" advertised instead. When they connect to this duplicate SSID they...
HI everyone. I just noticed this. I have different series of AP , 1142 , 1252 , 3500 , 3700. it is happening on any series. if I set the duplex and speed to Auto some of my AP are connecting with 100mb not 1Gps. if I set duplex to full and speed to 1...
Hi Guys,My company is looking at installing the Cisco Wireless LAN Controller software for managing our Access Points and promoting BYOD (Bring your own device).We currently operate 6 sites throughout the country all connected by WAN. We currently ha...
I have an MR32, and I create a single SSID on it.My iPhone and my laptop were connected to it. My iPhone and my laptop can ping each other.But, the iTunes on my laptop can't find my iPhone through this SSID.By using Wireshark on my laptop, i just can...
Hi,I am interested to know how can i set alert on dashboard so that i can get email notification for any specific client about its connection and disconnection from network.Please help it's there in dashboard.
I am fairly new to the Meraki environment so please excuse my lack of knowledge with the dashboard and equipment.So we have a few MR46's that are registered in the dashboard but have not been connected to the Cisco network yet.There is 1 MR46 that ha...
I've got a 2504 WLC with AIR-CAP2702I-A-K9 APs. Software on the WLC is 8.0.132.0 Issue is with a single WLAN when getting IP addresses via DHCP. These APs are in local mode as well, so CAPWAP tunnel is built to the WLC.This SSID is in the 10.2.1.x ne...
We are in a bind and need to implement a controller using 8.10 and being deploying 9120APs. The main controller is stuck on 8.5 due the number of older 3502 and 3602 APs. I've always thought the version of AireIOS on the controllers had to be consi...
Hi In WLC, from WLANs -----> Advanced -----> AP group -----> we can see blue triangle on the right side. When moving mouse on it, it can show several choices. One of them is NAC Enable. Please see the below screenshot. NAC is part of ISE. We can thin...
Hello everyone.I have the next problem, Attach an evidence log:###########################################################Octeon cust_kukrip2(ram)# fatload usb 0 0x20000000 AIR-CT3504-K9-8-5-131-0.aes** Bad device usb 0 **Octeon cust_kukrip2(ram)# st...
