Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

review


Labels

Forum Posts

We've been reviewing some options for our client and are able to get our hands on -A 9120axi wireless access points but some locations these will be installed in will be US based.  I know US runs on -B regulatory domain now, however at some point -A ...

netgn by Level 2
  • 4228 Views
  • 5 replies
  • 5 Helpful votes

I plan to start using FRA to manage the roles of my XOR radios.  I've enabled FRA with the radio roles set as static for now.The coverage was designed for 5Ghz, so the 2.4 coverage is currently too dense.  TPC is setting most of the 2.4 radios to 2 o...

Resolved! migrate/upgrade

hi, we have 2 cisco controllers 3500 8.5.161.0 in HA, and same mobility group, (100AP:AIR-CAP2602I-E-K9 and AIR-CAP2702I-E-K9 ).We buy new APs  9120 to upgrade this solution. So, do u know some procedures how to migrate from old devices to new ones? ...

jiripijacek by Frequent Visitor
  • 956 Views
  • 2 replies
  • 0 Helpful votes

HiWe have a Cat9800 controller with aWIPs enabled and it is sending alarms to a DNAC appliance.  I am seeing quite a lot of alarms that, if they are real, would suggest we have an inordinate number of Wifi attackers in our office.  The most frequent ...

KevinR99 by Level 5
  • 1354 Views
  • 3 replies
  • 0 Helpful votes

Hello all,I am trying to connect to wlc gui which is on vlan 20 from user vlan 25. I could get ping replies and tracert reaching the wlc but not able to get the https on browser working. We dont have ACLs on layer 2 in vlans. There is a port channel ...

sakthilokesh by Frequent Visitor
  • 1636 Views
  • 2 replies
  • 0 Helpful votes

I'm trying to get some feedback from users who may be using 9800-CL. Are you doing FlexConnect or Local Mode? If you are doing Local Mode any performance related issues and/or any other caveats using the virutal environment? I see FlexConnect as an o...

ALIAOF_ by Level 11
  • 3119 Views
  • 4 replies
  • 0 Helpful votes

Hi,I've seen a couple of posts with similar problems, but I'm looking to understand the problem a bit deeper.I have MS120 switches, MR44 APs and two SSIDs (guest and internal).I would like to tag guest with vlan 10 and internal with vlan 20 but the p...

br_BlueTie by Community Member
  • 5103 Views
  • 4 replies
  • 0 Helpful votes

Hi We have 2 WLC 5520 configured as HA. One of them stopped working and was replaced with a new.Now the Web Auth doesn't work if we have the new WLC active, we get 404 not found on the client.If we switch active WLC and let the other that we haven't ...

Hi Team, A long while back I bought an AIR-AP-1252AG from some company that were getting rid of it.I got into the device but couldn't figure out what I was doing wrong.About 2-3 years went by and I finally had the courage to tackle this problem. Rece...

bendall19 by Visitor
  • 2698 Views
  • 11 replies
  • 0 Helpful votes

Dear Community,Please I need help from you, our collaborator claims that there are cuts on the Webex sessions because of the wifi connection, we have an AP2802E-E-K9, how can I troubleshoot to know where is the issue? Thanks in advance;

NasTar by Visitor
  • 3110 Views
  • 12 replies
  • 5 Helpful votes

Hi,We recognize that InterfaceGroups in AireOS and VLAN Groups in Catalyst 9800 are functionally equivalent.When multiple VLANs are assigned in InterfaceGroups in AireOS, the corresponding VLAN is assigned from the client's static IP. It works perfec...

nono1200 by Visitor
  • 1036 Views
  • 1 replies
  • 5 Helpful votes

AppleTV can support 802.1x  WPA/WPA2 on used to Apple Configurator 2.But, CME GUI set WPA2 only.CME CUI view :ーーーーーーーーー(Cisco Controller) show>wlan summary:3      AppleTV_GP / AppleTV_WiFi                                                Enabled   mana...

Review Cisco Networking for a $25 gift card