Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hello, can someone help me with information please? I have 4 Cisco AP equipment, AIR-CAP2602I-A-K9, none of them I can use since I don't have a controller, but it strikes me that I can't even connect by console cable I have used putty, teraterm, moba...
Hi, i have 2 AP´s 2802e with the Mobility Express Software on it.I used the WLAN Provision to do the initial config.After this i install a dhcp so the two AP can find each other.Mobility Express: static IPAP: DHCPNow i wanna have static IP for the tw...
Hi There! I know it is possible using CPI to collect historical logs of users associated per ssid but is it possible to leverage WLC to get historical logs of users associated per SSID for at least a month? The goal is to determine if users are conne...
How could I know the IOS version of an ap other than connecting to it?
Currently testing the new 9800-CL controllers and we've gotten an eval of the CMX on-prem appliance to replace our existing MSEs. I'm able to get CMX connected to our production AireOS controllers but there appears to be an SSH issue when trying to a...
Resolved! Cisco 819 ISR / Access Point issue
I am having an issue with my Cisco C819GW-LTE-MNA-AK9 ISR, when I try and connect to the embedded access point. It gives me a message stating the connection is refused. This is a new ISR and I had never configured it before, any assistance and /...
Hi all,I have a topology as below:VLAN 1: default, and nativeVLAN 16: wifi 1VLAN 17: wifi 2VLAN 110: managementOn WLC, I config the management VLAN:IP: 172.1.6.2Subnet mask: 255.255.255.0Default gateway: 172.1.6.1DHCP: 172.1.6.1Port: 1VLAN identifier...
Resolved! unable to create trustpoint on 9800-cl
So I've been trying to setup a 9800-CL a few times on my intel nuc here at home (only one NIC). I'm got it up and running on esxi 6.7 but I can't create a trustpoint and for this reason of course my access point can't connect. I have had nothing but ...
I have about a 100 2700s AP connected to a pair of controller in HA and out of that 100 I would like to move about 50 AP to another pair of Controller altogether, Can this be achieved with the help of Cisco Prime Templates tab, if so how, or any othe...
Hello All, We have a Strange issue , our Capwap tunnel between central WLC and Anchor WLC gets randomly down , and we run eping and mping between the Controllers the Tunnel gets back up. This issue is happening randomly but recently it happens ...
Good day.We have a customer based in Russia that uses WLC2504 + some of APs with R-reg.domain(1815i-R , 3702i-R, 3802i-R) Now now that customer bought some new APs that have E-reg.domain Is it enough to change the country code support on the WLC to m...
I need to know how we can configure HA between two virtual controllers. What are the physical connections? And settings needed to work?
Hello,there is a request from my customer to have dynamic bandwidth allocation to be made to a category of wireless users (VIP). While other categories (non-VIP) can get less bandwidth. When the VIP users are gone, the same bandwidth can be put back ...
Hi,I am using cisco 5760 , Currently the issue is facing slow http and https access Any advise Thanks
Hello, i have make this setup for the acess point and i get lost somewhere. i have a Cisco C887VA, router with secondary core for the acce point. version 15.3 no service pad service timestamps debug datetime msec service timestamps log datetime loca...
