Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Wireless firmware versions MR 31.1.8 changelogImportant noteWi-Fi 5 Wave 2 MRs support - This version and subsequent MR 31.x.x are only supported on 802.11ax (Wi-Fi 6) and newer MR models. 802.11ac Wave 2 and older products will upgrade to the backup...
Hello, we would like to use a custom WebAuth page on our Cisco 9115-AXI-E. Unfortunately, we can't get a logo to appear. The .tar file contains the logo file. A show bootsystem: also shows that the file is on the file system. Is there a trick? thanks...
Could you please some one tell us can i configure for 9164I AP in standalone mode in WLC mode and it will work.
Hello All - Hoping the community might be able to give me some help. I was using this document (https://documentation.meraki.com/MR/Wi-Fi_Basics_and_Best_Practices/Extending_the_LAN_with_a_Wireless_Mesh_Link) to setup 2 MR86 devices to MESH and exten...
Hii guys,I just want to know about the RF profile you set for your access points, why you chose it, and how you determined that it is the best profile setting. I also attached mine.2.4 GHz radio settingsRadio transmit power range (dBm): 5 - 30Minimum...
HiI currently have setup Sponsored Guest Authentication and all is working as expected, although we would like the ability of the sponsor to set the duration of access upon authorising the access, is this possible?Only currently an admin to the dashb...
bom dia estamos tendo erro para autenticar nosso w-fi com o Gmail, fala ( to connect to this network using your Google Account, plense open the Sign-In page in a web browser on your device using the following instructions.
Hello, I have a Cisco wlc 9800 running on 17.9.6 and it's working fine. Once I'm upgrading to 17.12.3 or 17.12.5 or 17.15.3, all Radios are down on 9166I-ROW APs. There is one outdoor AP 9124 which is working fine on those IOS version. 9124AX has -E ...
Hello all, is there a way to configure Radius - call-station-ID and NAS-ID from the GUI of the WLC? I found this guide https://www.cisco.com/c/en/us/td/docs/wireless/controller/9800/17-9/config-guide/b_wl_17_9_cg/m_radius-call-station-identifier.html...
Good DayWe have a few Ap's C9115AXI-E , manufacturing date 04/22 .Other Ap's will be plugged into the network and they will see the WLC automatically . These once keep on booting . I believe the fix on Cisco's website is not applicable with these spe...
Wireless firmware versions MR 32.1.3 changelogImportant noteMR45/55 APs are not supported on MR 32.x.x and will instead upgrade to the backup version (MR 31.1.7.1) if they are in networks configured for MR 32.x.x versions, and thus, new features will...
Select IPV4 check-box in the General tab, update the fields as per the below image, and then click Click Update & Apply to Device. After performing above step the C9115AXE-D wireless AP continuously blinks Red/Green.Whereas performing same action...
Hi Currently, WLC9800 is a WAP3 only configuration, and when you try to connect Apple equipment to wifi, you often find it looping like a picture. Have you ever seen this?
Hello.I have a question.I purchased a CW9176I (configuration management from the cloud).I conducted a simple test before delivering it to the customer.I connected 200 virtual wireless devices to the AP(Radio2),but only about 150 could be connected. 5...
Hi Everyone,Seeking for your help if there is any resolution on my issue encountered.As of now, some of my users is not able to connect with wireless connection from the captive portal. I have done some packet capture during the authenticatiom until ...
