Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
HI, I have two question about wlc:1\Is there any method to check drop packets on wlc interfaces or ports ? For example, the output just like "show interface e x/y " command on switch.2\Whether we can capture data plane packets on wlc ? And how to do ...
From time to time our HREAP-WLAN-APs are no longer able to accept client connections.We have to reset them to get rid of the problem, which creates the followoing Log-entries in the WLAN-AP:*Jan 23 05:56:30.387: %DOT11-4-DTXPOISON: DTX marked with po...
Hi board, I'm just browsing the 8.2 configuration guide of the WLC and stumbled upon this: With FlexConnect local switching, Multicast is forwarded only for the VLAN that the SSID is mappedto and not to any overridden VLANs. Therefore, IPv6 does not...
Hello All, I initialized and configured Mobility Express access point with necessary parameters. CDP neighbors all shows that the access point is connected to a switch.I can't figure out why the access point LED is flashing different colors and also...
Hi All,I have SD-Access fabric network with DNA Center. I have one main wireless network which is fabric as well and 802.1X authentication. I use 3500 series WLC and 1850 series APs. The problem is as shown below picture. I got constant timeouts in m...
Can someone please help with documentation about the new ap 2802 or tell me what can i do to get out of this prompt and join to a WLC.
Resolved! WLC HA redundancy statistics ！
Hi， I dont have wlc for testing.I want to know what is meaning of “ping request and response” in wlc GUI “monitor > redundancy > statistics”.Is it represents do a auto ping or manual ping on active wlc and standby wlc? And whether the “sent to peer” ...
HI Everyone, I looked at the interface details and noticed that all dynamic-interfaces have the same MAC address. And it is basically the same as the MAC address of the management interface. My WLC is 5508, and I want to know how the Cisco WLC assign...
Anybody know what is the correct path for upgrading appliance MSE 7.6.100.0 to MSE 8.0.150.0? The 8.0.150.0 release notes is confusing at least. https://www.cisco.com/c/en/us/td/docs/wireless/mse/release/notes/mse8_0_150.html It has a section with a ...
Hi, For security reasons I need to regenerate the certificate for the https management GUI of a WLC 5508 SSO, since the hash algorithm that has the self-signed certificate of when it is installed is SHA1 and I need it to be SHA256. I have been able t...
Is there a way to limit the number of logins from a particular set of credentials in Cisco Prime 2.1? I want to set a maximum of 2 logins from a particular user on the wlan. I have a guest wlan using layer 3 security and an internal wlan using RADIUS...
Hi all I have a question about the WLC N+1 redundancy. I have 3 Cisco WLC 5520. Can i configure one as Active, one as Standby and the last one will take over when the active and the passiv are down. The failover should be like this.1. Active fails2....
HelloI have a cisco controller 5520 with more than 300 access points joining it, I found that most of the access points like 250 out of 300 are working on the maximum power level 1 on 5g band only, while on 2.4 bands the power level is within normal ...
We are implementing a VLAN in a confined environment which combines both wired and wireless connections. We currently have multiple Full HD (1920x1200) video cameras, each streaming >3.3Gbps, so we are using 10Gig switch over RJ45. The video is multi...
please is there any one help me in this issue *spamApTask1: Nov 20 13:01:57.053: #LWAPP-3-REPLAY_ERR: spam_lrad.c:37692 The system has received replay error on slot 0, WLAN ID 2, count 3 from AP 28:6f:7f:0c:62:30*spamApTask5: Nov 20 13:01:15.593: #L...
