Our customer has several 1852 indoor APs powered by power injectors. Recently a few of them stopped working. Inspection shows that there were burnt marks on the boards near the AP's power supply circuit.We are wondering what could have happened. Can ...
Forum Posts
Resolved! Help with AP 1850 software upgrade
Dear all, Could you pls help me to resolve the current situation: I've tried to upgrade the AIR-AP1852E-E-K9 (Mobility Express mode) from 8.3.112.0 to 8.10.130.0 and something went wrong.# I downloaded the software, installed TFTP server in my lapto...
Dear AllI did configuration follow config guide this link "https://www.cisco.com/c/en/us/td/docs/wireless/controller/ewc/17-2/config-guide/ewc_cg_17_2/secure_ldap_.html" but i don't see log request or receive from WLC to LDAP =======================...
Hi.I'm doing a lab, I have a 2802i AP as the mobility express controller, and I want to associate a 2602i to it, but I'm getting this error in the console of the 2602i: *May 21 20:30:15.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip...
Hi all,After adding a 9800-CL to Prime I got a critical alarm. Does somebody know the reason for this?Catalyst 9800 Telemetry coral connection failure for device IP 10.1.51.11. Please check the coral connection.Many Thanks!Regards, Urs
Hello, Although configuring the C9800 from CLI, even RMI SSO, when I'm connecting via HTTPS to the controller, the following is displayed: "This device is detected as a factory-fresh device. To begin, Click on below cards to create a new user account...
Hello, we'd like to set-up workgroup bridge feature on new Catalyst 9800 WLC with transparency for VLAN-ID's (trunk via WGB) like on following link: https://www.cisco.com/c/en/us/support/docs/wireless-mobility/service-set-identifier-ssid/211293-Conf...
Hello, I'm trying to connect 2 Cisco C9800-80 together for HA using Release 17.1. I was wondering If I was able to do the following. My two WLC's are in two different in DC's. I want to be able to use RP and RMI. The RP ports for each WLC would b...
Resolved! Mesh over Ethernet Configuration
Hello,I was currently handed the following equipment and asked to make a wireless bridge to a permanently docked ship.1 x MX642 x MR702 x MR361 x MS120 - 8 FP1 x PoE InjectorThe thought process is that we would set up the MX64 on land and connect it ...
Hello, Our Cisco Prime doesn't want to load it's webpage today, has anyone experienced this before? I will be de-commissioning it at some point as we have another Prime server, but I need to get the floor plans off it. I can SSH to it though, so I'm...
Our wireless infrastructure is based on WLC5520 with 1852i APs. I can see ipads (not IOS dependend) iphones often dissasociating and directly reassociating on the same AP. Normally that´s no problem, but this break leads to an interruption of, for ex...
my signal booster has a continuous fast flashing green light which i gather means that it is in th "configuration cycle" but never seems to stop.. ive pressed the reset button several times and even tried holding it in for 10,20,30 seconds over the l...
Hi Team, We have experiencing some problems with this APs. Let's see if you can add some light. We connect the AP to the network with Internet access and connect to the AP through the SSID Provisioned, after that we configure the WLC with static IP a...
Hi Experts, Do you know any information about Ingress Protection Rating (IP) of Cisco Access Point 1850 ? I cant find any docs online mentioning about this Access Point. I only can find Cisco Access Point 15XX , which has IP67 Thank you very much...
Resolved! Why tagged vlan cannot work in vWLC
Hi, Here is a question. Diagram is like this: Switch-f0/20------PC(vmware-workstation-vwlc, bridge connection)switch vlan 10 ip address 10.0.0.1/24PC ip address 10.0.0.2/24vWLC management ip address 10.0.0.3/24 untaggedinterface f0/20 is in vlan ...
