Hello, if I have a current WLC and it will be upgraded by newer one, can I use the old WLC and convert it to be SKU unit or this should be hardcoded at the ordering phase 2- Also what will happen with the license on the SKU unit, does the 90 da...
Forum Posts
Hi everyone, I want to show a web page on client's browser following client connect a wlan.. I m not strict on showing web page, it might be "alert message" too.. Is that possible Note: WLC: 5508 Thank you Huseyin
Caro, Estamos trabalhando com o WLC8500 diretamente conectado ao equipamento central da rede, e precisamos conectá-lo a um equipamento de distribuição (SWL3), já que o WLC tem 2 interfaces, e estamos usando "apenas 1", no entanto, estamos estudando a...
Hi, i have the problem that my Cisco 8821 won't connect with protocol 802.11 a/c. All 8821 Phones connect with 802.11a/n? 802.11a/c is enabled on the WLC and i tried several WLC Versions 8.0 / 8.3..... We use the Cisco 2702 Access Points. The...
Resolved! 802.1x with MAC authentication
Hello experts, I want to implement two factor authentication for specific users group. via AD + MAC authentication.. I want to create (Auth annd AuthZ) rule in ISE to allows specific users Group (from AD) and with there mac address. Could you please...
Hello, I need to implement AP groups in a Cisco Mobility Express Environment. In a production environment, WLANs (and clients too, as a consequence) take any subnet (VLAN) created in the AP master. I'm sure this does not happen under a WLC...
Hi all, i am detecting an issue with WLC 3504 version 8.5.135. Users with iPhone7/8/10 are not able to connect. They join to the network, receive IP address but it seems they are isolated. Same users connected on WLC5520 version 8.5.135 are able to n...
When enabling 5G on the XOR radio, power level is stuck on level 8 (weakest). Even when i disable the native 5G radio - so only the XOR radio is enabled, the power level is still at 8. Tx power level assignment is set to Global, When selection Custom...
Resolved! CRL check WLC and AP
Hello, Is there an option to enable CRL check on an AP and controller running on 8.5? I have LSC enabled and was able to issue certificates to both the AP and the controller with the CDP extension present in both but I don't see an attempt to fetch...
Resolved! Cisco vWLC ports total traffic
Hi, In Cisco WLC 8.7.106.0 release notes I see that a vWLCs can have the ports total traffic of 500Mpbs (in FlexConnect central switching mode). I think that in FlexConnect local switching mode the total traffic limit (per AP) would be the AP Ether...
Hello, Does anyone here on the forums know if there is a way to adjust the RSSI so that its lower on Controller based AP's without making that change globally? I have a location where when the users roam between the AP's the calls are dropping. R...
Resolved! AIR-AP1852I as standalone
Recently I bought an AIR-AP1852I to use in my office.I have never had a Cisco product before. We always had some cheap consumer APs before. I connected the AP to the energy, and connected the POE port to a switch on my network.The AP started showing ...
Hi, I am trying to find a document on how mobility express deployment handles wpa2-enterprise authentication. The question i have is: Do all APs authenticate against clients against the radius server directly, or does the leader of the ME deploy...
Good day, Everyone! I'm having a minor problem with WLC 5520, I say it's minor because it doesn't really affect the wireless network of the client but of course client want to fix it. The setup is that there are 2 WLC currently on HA. The active...
I was previously running 8.5.131 with FRA and DCA with "best" channel width, using 2700 series AP's. With .131 the DCA selects an 80MHz bandwidth for the 5GHz band on all three AP's. With .135, it reverts back to 20 MHz. To me this seems like a bug. ...
