Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

review


Labels

Forum Posts

Hi,I don't want to use the Service Port\OOB Interface Gig 0 for Management. The preference is to use 2 x 10GB Uplinks in a  Port-channel between the WLC and Neighbouring switch for my Management and WLAN Vlans.This config matches exiting 5508 WLCs. O...

iwearing by • Level 5
  • 4148 Views
  • 5 replies
  • 0 Helpful votes

Hi, I have problem connecting out of the box Air-AP1852i-E-K9 to my working WLC2500.   WLC 2500 running firmware:  7.6.130.0 AP1852 running firmware version:  AP Running Image     : 8.3.143.0 initially I checked that the time was wrong on the AP and ...

C K by • Level 1
  • 7268 Views
  • 9 replies
  • 0 Helpful votes

Hello As CAPWAP AP, the AP1701 gives maximum of 400 Mbps data rates to the clients. But when we set the AP1701 as Autonomous, it gives maximum of 144 Mbps only.  How can I get 400 Mbps in Autonomous mode ? ThanksCleetus

cleetusant by • Level 2
  • 6291 Views
  • 10 replies
  • 0 Helpful votes

I have read through the Meraki's AP configuration guide about MAC address filtering, and see that it only support via "Association requirements" with "no encryption."In non-Meraki, Cisco-based Wi-Fi infrastructure, you can use both WPA2 encrypted dat...

Dan_Andolsen by • Community Member
  • 16880 Views
  • 4 replies
  • 0 Helpful votes

Is it possible to create an SSID that only broadcasts the 2GHz channel on the MR33 Access Point? I have some devices: Apple Watches, Thermostats that only work on the 2GHZ channel. I haven't been able to find anything stating it can or can't be done.

JStarks by • Community Member
  • 36569 Views
  • 20 replies
  • 0 Helpful votes

I have a weird issue here.When I tried to use vWLC(running in esxi) to manage my APs(2800 & 1800 series), any devices connected to these APs cannot ping the gateway (actually like 90% icmp packet no reply), these devices will show 'No Internet'. But ...

glonk__ by • Visitor
  • 2669 Views
  • 2 replies
  • 0 Helpful votes

Hello Cisco community,I need ur help. I have EPC3925 router/modem problem. I searched for hours but i just cant find bandwidth control on 192.168.0.1 site. I need to set net speed (per ip) of some users on my wifi network. I've done that easly on the...

Hello,I have a fabric network both on wired and wireless configured by DNA Center but because of internal DNAC problems I modify WLC manually. Both Wifi and Wired are in the same network. When my Laptop and Chromecast both are connected with cable an...

HI guys,I got a 5520 Wireless LAN Controller with 8.3.143.0trying to connect AIR-AP2802I-K9 with running image 8.5.140.0just to let you know I have connected them on a local switch on a testing environment as im using this for a bigger project im ver...

zumriatha by • Frequent Visitor
  • 4359 Views
  • 5 replies
  • 0 Helpful votes

I have some access points that were with this message "Radio reset due to (56) Radio channel set" They were working with DCA best, after I switched to 20MHz the problem stopped occurring. this problem only happened with the 5GHz radio. Has anyone see...

Edu by • Level 3
  • 6879 Views
  • 6 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card