Hello. Can we change CW9162I-E to MR? If yes, then how?
Hello. Can we change CW9162I-E to MR? If yes, then how?
There is a drop down now next to a field that says, SSID Admins, by Default its set to "access disabled" all of my SSID's are working just fine.so Wondering what this Drop down is for, why it defaults to disabled and why would I want to enable itthan...
It remains blinking green and is not recognized by the network.The application does not recognize it either.
Hi all,I saw that there is finally native support for Entra ID authentication over Wi-Fi ,great news!However, I’m still not sure how to actually link Meraki with Entra ID.I found some documentation on how to configure the SSID, but I couldn't find wh...
Hi does anyone know what model of Meraki device has serial number beginning Q3AT- xxxx-xxxxI have 6 on a spreadsheet that don't show up on my dashboard. We use MR42, MR44, MR76 so it isn't one of those.
CW9176IMR 32.1.2I am setting up in the cloud.Where is the Preamble Puncturing configuration item?Is it always enabled?
Hi all,I’m working with a Cisco 9115AXI AP in FlexConnect mode and need to deploy two SSIDs:Guest (central switching, tunneled via CAPWAP to the controller)Corporate (local switching)Is this supported on a single AP?What I’ve configured:AP is in Flex...
Hi! We have a strange issue. We use 9800-40 WLCs in HA-SSO deployment model. There is an WLAN network, clients authenticated by an external RADIUS server using certificates. If administrators use small certificate chains, authentication works perfect...
Cisco AireOS Version 8.10.196.0,The power supply was changed to dc 48V1A, and POE 30 W was also tried, but there was no signal,You can't see the wireless access pointcisco AIR-AP4800-B-K9 ARMv7 Processor rev 1 (v7l) with 1028200/447120K bytes of me...
Hey everyone,We recently changed mailservers and now I can't get our RVS4000 to email logs via SMTP. We just started using google apps, which run SMTP through port 587 and require authentication. Is there any way of getting the RVS4000 to use a non-s...
What is the possible cause of this 0.0.0.0 IP address? When I try to check these devices, they have already transferred to another AP. We also have scenarios where they seem to degrade the internet connection on the current access point, especially w...
Hey Folks,We’re excited to share Cisco Wireless has partnered with Assa Abloy to enable seamless connectivity between MR Access Points and Assa Abloy's Vingcard Electronic Door Locks.HighlightsSupported Cisco Wireless Access Points can now function a...
To all cisco gurus,I am first time Cisco user and struggling configuring the Cisco AP. I have connected the Cisco AP with PoE Switch. The AP is in operational state LED Alternating between Green and Red as per user manual https://www.cisco.com/c/en/u...
Best way to change 9800-40 wlc hostname and IP address, including all APs?
Hi There.We are facing a frequent disconnection of our Wireless Clients on our Meraki MR44 access points. We are running the current stable release 29.4.1 on all our access points.The user is stationed at his desk and he gets disconnected frequently ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 11-17-2026 11:43 AM | ||
| 10-15-2026 05:58 PM | ||
| 10-12-2026 06:46 PM | ||
| 09-30-2026 07:34 AM | ||
| 08-10-2026 11:32 AM |
| User | Count |
|---|---|
| 4 | |
| 2 | |
| 2 | |
| 1 | |
| 1 |