Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Hello, I have 2 WLC with 2 SSID and I have seen the IPAD have problems to connect to wifi. They try to connect but sometimes do and sometimes do not. Then they say: "impossible to connect to wifi X". This only happens with IPAD or iphones, not with o...
Resolved! wlc2504 Dynamic VLAN Assignment
I installed DHCP, Radius in Ubuntu to configure Dynamic VLAN Assignment.I can get DHCP and log in as Radius. I want to use several VLANs for one SSID.But I can't.https://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-vlan/71683-dynamic...
Dear Sir,How can i transfer license my smart domain to client domain?
I have a 9840 that I setup from defaults on the CLI. How do I get the GUI out of express setup?I cannot find this anywhere in the configuration guise. Also, what do the different "install modes" such as "install" or "bundle" modes.How do I change the...
Hello all. I am facing a strange issue on a deployment of 34 Meraki APs, Users on site are not roaming to the nearest AP.The site is mostly made of mac book pro and Apple and android devices.There are 5 SSID’s each on there own subnet. Capacity d...
Just started to investigate a medium/large network setup where it seems all of the LWAPs are connected to switchports configured as trunks and all of the LWAPs are in local mode. Each switchport is configured like this... interface GigabitEthernet2/0...
Dear Experts, I have two questions about Cat9800 WLCs TACACS+ admin access configuration. 1. Once 9800 is configured to do TACACS+ for its webUI admin access, no matter if logging with WLC local admin accounts or AD accounts, there are always two use...
Resolved! AIR-AP1815I-E-K9 from CAPWAP to ME ?
Hello community,Is it possible to convert an AIR-AP1815I-E-K9 access point to ME (Mobility Express) version ? Already have some K9-C version working, but ME portal is unable to upgrade those K9 by itself. Thanks for your advises. Anthony
Hi Team, I have configured TWO VLANS for LAN and WIFI... Wifi is configured and connected on ASA MaManagement port and wifi is working finewe are not able to access from Wifi vlan to lan VLAN Can any one help me to resolve the issue thankssuresh
Hello Meraki Community,I have been told that the Meraki Layer 7 Firewall solution available in Meraki MR AP dashboard is based on best effort, as it is not able to block certain traffics even if they have been defined within the Layer 7 firewall rule...
Hello, I have just setup a test vWLC in a lab and connected a AIR-CAP2702I-E-K, the controller can see the AP, I have configured a few SSIDs but I cannot see them being broadcasted?Any suggestions? Wireless
Hello together, i am currently struggling really hard to get a AP2802i to run as a Bridge / WGB Mode. I have the CAPWAP Version and the Bridge-mode should be available, but its NOT. When i try to change to mode from "local" to "bridge" i get this Mes...
Using a WLC 5508 and ACS for web authentication for users wireless users. The virtual IP 1.1.1.1 has been always set to take the users to the authentication page. All of a sudden it stopped and is now sending users to the page attached. Can someon...
Is it possible to provide locally switched guest wireless access in flexconnect mode with Web-Auth? All of the documentaion examples I can find show guest webauth with central switching. I want a remote office, connected via DMPVN, to provide guest w...
Resolved! IPV6 addresses on Dynamic Interfaces
Cisco 5520 / 8.5.140Starting to roll out IPV6 testing on the WLC and I'm running in to trouble adding vlans with IPV6 interfaces to the controller.I've added 1 dynamic interface (vlan 120) with a ipv6 address / 64 / and the link-local address of a ro...
