I have a 9840 that I setup from defaults on the CLI. How do I get the GUI out of express setup?I cannot find this anywhere in the configuration guise. Also, what do the different "install modes" such as "install" or "bundle" modes.How do I change the...
Forum Posts
Hello all. I am facing a strange issue on a deployment of 34 Meraki APs, Users on site are not roaming to the nearest AP.The site is mostly made of mac book pro and Apple and android devices.There are 5 SSID’s each on there own subnet. Capacity d...
Just started to investigate a medium/large network setup where it seems all of the LWAPs are connected to switchports configured as trunks and all of the LWAPs are in local mode. Each switchport is configured like this... interface GigabitEthernet2/0...
Resolved! AIR-AP1815I-E-K9 from CAPWAP to ME ?
Hello community,Is it possible to convert an AIR-AP1815I-E-K9 access point to ME (Mobility Express) version ? Already have some K9-C version working, but ME portal is unable to upgrade those K9 by itself. Thanks for your advises. Anthony
Hi Team, I have configured TWO VLANS for LAN and WIFI... Wifi is configured and connected on ASA MaManagement port and wifi is working finewe are not able to access from Wifi vlan to lan VLAN Can any one help me to resolve the issue thankssuresh
Hello Meraki Community,I have been told that the Meraki Layer 7 Firewall solution available in Meraki MR AP dashboard is based on best effort, as it is not able to block certain traffics even if they have been defined within the Layer 7 firewall rule...
Hello, I have just setup a test vWLC in a lab and connected a AIR-CAP2702I-E-K, the controller can see the AP, I have configured a few SSIDs but I cannot see them being broadcasted?Any suggestions? Wireless
Hello together, i am currently struggling really hard to get a AP2802i to run as a Bridge / WGB Mode. I have the CAPWAP Version and the Bridge-mode should be available, but its NOT. When i try to change to mode from "local" to "bridge" i get this Mes...
Using a WLC 5508 and ACS for web authentication for users wireless users. The virtual IP 1.1.1.1 has been always set to take the users to the authentication page. All of a sudden it stopped and is now sending users to the page attached. Can someon...
Is it possible to provide locally switched guest wireless access in flexconnect mode with Web-Auth? All of the documentaion examples I can find show guest webauth with central switching. I want a remote office, connected via DMPVN, to provide guest w...
Resolved! IPV6 addresses on Dynamic Interfaces
Cisco 5520 / 8.5.140Starting to roll out IPV6 testing on the WLC and I'm running in to trouble adding vlans with IPV6 interfaces to the controller.I've added 1 dynamic interface (vlan 120) with a ipv6 address / 64 / and the link-local address of a ro...
Exact behavior desired is Guest WLAN clients will see a webpage built-in to the controller that will warn them of our policy, but they will not have to enter a password--they will only need to click on an accept button. Is that doable on the 5508 run...
Hello, I'm wondering if when you set multiple mandatory data rates, example 3, that means a client MUST support these 3 data rates or it has to support one among the 3 mandatory data rates ? Example, most of our rf profiles 5Ghz Data Rates are config...
Just wondering if there is a workaround to supporting two factor authentication with the Client VPN. The url here says it doesn't without using a third party tool: https://documentation.meraki.com/zGeneral_Administration/Other_Topics/Two-Factor_Authe...
We are happy to announce the second refresh of 8.10MR1 Beta Program for PRODUCTION deployments. 8.10.109.48 is the second, qualified Beta Image and is fully BU supported. After previous 8.10 CCO, this program is focused on hardening the software qual...
