I was working on a maintenance window. moving some customers to our new MPLS network PE router NCS540 SOFTWARE 7.6.2.When I move 192.168.70.0/24 to the new mpls network I was able to ping it from everywhere. however a static routed network I was...
Forum Posts
In our lab, we are testing EVPN with multihomed active/standby. Both Cisco NCS540s are connected to the same C9300 on the LAN side. Rerouting in WAN and loss of the LAN-link gives a failover in ms. But a reload, or even worse a power-loss, brings the...
Resolved! NC57-MPA-2D4H-S 400G error
Does anyone have experience with NC57-MPA-2D4H-S and telling them they should be 400G? Installed on NCS-57C3-MOD-SYSI am following this guide a Cisco Doc: Interface and Hardware Component Configuration Guide for Cisco NCS 5500 Series Routers, IOS XR ...
Hi Community, I need to enable a connection by STM-1Channelized to map E1s from pseudowires with this hardware. ASR 9010RSP800 - XR 7.5.2 / 7.9.21A9K-48X10GE-1G-SE or A9K-24X10GE-1G-SESmart SFP - SFP-CH-OC3STM1-I https://tmgmatrix.cisco.com/?si=SFP-C...
Hi Guys,Does anybody know an equivalent of “default interface” for IOS XR or a smart way to delete hundreds of attachment circuits for single physical interface?Appreciate your comments.Regards,Vasil
Hi,I have policing on an interface (in an asr9901) which works just fine policy-map police-max2gbps class class-default police rate 2200 mbps burst 432537600 bytes peak-burst 865075200 bytes conform-action transmit violate-action drop end-policy-map...
Hi everyoneWe have an asr9k-x64 (V7.9.21) with an A9K-48X10GE-1G-TR linecard.we have bundled 8 TenG Links to BE5 with the following configs for each vlan: interface Bundle-Ether5.10 l2transport description VLAN10 encapsulation dot1q 10 rewrite ingre...
ncs5501 - stuck in sysadmin mode - how to return to router rp0 user mode
Hi! I followed the walkthrough and the guide to set up an IPoE BNG router with ASR9001 from xthuijs. Everything has worked flawlessly for the last 4 years or so. My concern is relative to the requirement of the unnumbered (from a loopback interface) ...
Resolved! BGP route reflection problems
Hi,I'm having trouble with BGP's route selection criteria. I have a network with NCS 5500; one of them is route reflector and receives route 1.46.0.0/19 via iBGP through three of my routers (R1, R2 and R3) with the following metric.R1:AS-PATH: 2914 1...
Hello,doing some ntp setup on XR and I observed something odd - i believe this behaviour is not expected but would appreciate feedback from ppl that have dealt with XR NTP behaviour. config is belowSo I configure two upstream servers "10.10.10.64 and...
Resolved! Nexus ISO to XR config rewrite
Hi, I'm doing a planning of Nexus 7k swap with NCS-57C3 routers. I'm wondering if Cisco has a config converter. Thanks
Hello, have couple of NCS-5501-SE (version 7.5.2) routers. I would like to reset the current configuration.What would be the most recommended way ? Do commit replace is still relevant for resetting the configuration ?I've read that some people are do...
I want to write in the event manager if the ping is not successful (Success rate is 0 percent), then you need to execute clear crypto ikev2 sa "x.x.x.x" Check available IP once every 3-5 minutes. Maybe someone will share the script.
I need to do an RFC2544 test with software loop on the interface between RFC2544 tester and Cisco kit. Has anyone already done this test with a single test device (1 interface) if yes I'm looking for configurations for ASR9K
