Trending Topics
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
-
how to see the line vty session time-out in NX-OS
by Sudqi -
IPSec VPN "Up-Active" but No Traffic Passing Between Cisco and Bintec
by Thomas27100 -
the self-registration page of guest wifi portal is not being updated
by seanxiao -
GRE over IPSEC
by georgesofroniadis -
BYOD - Network Setup Assistant (NSA) on Android and random mac address
by Daniel G. -
cisco sdwan vmanage configuration-db lost password
by hbejinha -
Webex app and Webex Meet app- Which to use for streaming live event?
by bbb bbb -
Cisco ISE: support for /31 subnet mask on ISE Interface ? (RFC3021)
by ffischer
Community Activity
Unable to claim target in EU region
Hi.When I'm trying to claim a new target from my Sandbox in Intersight I get the message:"The device has not been updated to support claim in this region. Please wait for device to be upgraded, if issue persists please contact Cisco TAC.". How can I ...
lost connection from DMVPN Peers
hi,i would like to express my issue and if you are able to advice me . i have a company router IR1101 with internet connection provided with private ipv4 address in the WAN interface. my company uses DMVPN in order to connect to company infrastructu...
Cisco 9200 err-disable AUTHMGR-5-SECURITY_VIOLATION
Hi Expert,Recently, one port on our 9200 switch went to err-disable state and the status LEDs are all off. The port configuration is as below: it is connected to a desktop PCThe logs is as below, it looks before it goes to err-disable state, the port...
IPSec VPN "Up-Active" but No Traffic Passing Between Cisco and Bintec
Hello,I am currently facing a recurring issue with the configuration of an IPSec VPN between a Cisco router and a Bintec router. Although the VPN tunnel appears to be functioning correctly and is displayed as "UP-Active" on both sides, no traffic is ...
how to see the line vty session time-out in NX-OS
Hello Experts,In Cisco IOS, we use (show line vty #) to see the session time-out for a specific user,what is the same command in Cisco NX-OS,Thanks
WS-C3650-24TS Switch software upgrade path
Hi, we are trying to upgrade WS-C3650-24TSL switch software to latest version that is 16.6.8, Where to find this software version upgrade path? will WS-C3650-24TSL and WS-C3650-24TSS switches supports stacking?
cisco sdwan vmanage configuration-db lost password
Hi,i lost my username and password for neo4j databasechanged it from default credentials neo4j/password i now i cant remember which is new password.what i can do? only tac can help it?is there any way to find at least the username?Regards,Hugo
Webex app and Webex Meet app- Which to use for streaming live event?
Dear Webex Experts and users,Just want to seek your expertise with regards to which app to use for a live streaming event. Webex app or Webex Meet app?thank you and best regards
Can ASA5555 License transfer to Cisco Firepower 2100 ASA?
Hi, We are migrating Cisco ASA5555 to Cisco Firepower 2100 ASA, is it possible to transfer the license that we have on the ASA5555 to the new Cisco Firepower 2100 ASA? if it is, can you please share the Steps and Procedure on how we can do that. Than...
Router Not Getting DHCP - Keep in Requesting & Purging State
Hi, My router not getting DHCP IP from ISP router. This issue sometime happen at my branch office. The only workaround I can do right now is shutdown the interface for 3 to 4 hours & after no shut the router able to get the IP. During the problem i c...
Resolved! Standard Access List
Hello,When i create standard access list with below item : access-list 55 permit 10.103.0.0 0.0.255.255access-list 55 permit 10.100.50.0 0.0.0.255access-list 55 permit 10.100.201.0 0.0.0.255access-list 55 permit 172.21.22.0 0.0.0.255access-list 55 pe...
Resolved! CVP UCCE 12.0 Payload
How do I configure UCCE 12.0 to use a certain payload for CTI?I've created a payload named CTI_Payload and added members (ECC variables).Now how do I tell the system to use it?
Cisco ISE: support for /31 subnet mask on ISE Interface ? (RFC3021)
Hi, one of our clients runs a 2 Node ISE Deployment in a lets call it "very specific" environment.New reqirements should be be fulfilled by keeping the IP Address on one of the nodes but move from /27 to a /31 subnet mask on the ISE Eth0 interfaces. ...
CCW-R
CCW-Rで更新用のQuoteを作成する際、対象の期間を一括で変更する方法は無いでしょうか？
Sub1098896の更新
CCW-RでQuote作成までは行けたのですが以下エラーが出てしまいます。 エラー解除いただけませんでしょうか。 An error occurred during validating the configuration. Please contact Cisco Customer Service. (C0132)
