Looking for Linksys NMH405 Setup software

Hi,Is there anyone here who has the installation CD with the Setup Wizard for the NMH405 mediahub?I lost the CD and can't find the software anywhere. Would be great if you can share (the iso file for example)Thanks, Bastienne 

Promiscuous mode error on FTDv 7.6.2

I upgraded my FTDv to version 7.6.2 and when i try deploying policy, it failed with this error: error : ERROR: cannot set np to promiscuous mode.ERROR: Failed to initialize interface,  Add interface Failed. Has anyone seen this and any workaround?Tha...

Network Design: New Collab Lab + Home Cloud/ Wifi

I'm considering a design change where I consolidate two WAN circuits behind shared edge hardware in order to better leverage some existing hardware. The environments are currently structured as:- 2 ISPs- 2 firewalls- 1 Layer-3 Switch- 3 access Switch...

NAT DIA Tracker on IPv6 Interfaces

Hello, does it make any sense to setup "tracker-type ipv6-interface" which track via HTTP probes ?  endpoint-tracker dns_t1 tracker-type ipv6-interface endpoint-dns-name cisco.com I tried several configuration but the probe still fails since mo...

air-lap1262n-a-k9 Autonomous ios

Hi , I'm looking for old device 1262n ap 's ios for Autonomous ver. If someone has it please let me know. Thank you all.

IBNS 2.0 with ISE for dot1x

Hi all Hope someone can answer the below for me.  Is a policy-map mandatory for dot1x to work when using IBNS 2.0 with ISE ?   I have two ports on a switch configured for dot1x. Out of the two, one is configured without any policy map and the other h...

Community Manager reflections on a celebratory year!

What an incredible year it has been as we celebrated the 25th Anniversary of Cisco Community! From exciting contests and vibrant social engagements to amazing prizes, this milestone has been truly spectacular. We were honored to connect with many of ...

OSPF WildCard mask problem

hi every one...i  am new in networking and i am bit confused in ospf  wildcard mask..ospf configartion on routers are as follow:R2(config)#router os 3R2(config-router)#net 4.1.1.0 0.0.0.6 a 1% OSPF: Invalid address/mask combination (discontiguous mas...

dual isp failover on single asr1002hx router

hi,please tell me how i can configure dual isp failover on single asr1002hx router. I have 2 internet wires from 2 isp. I have /28 from ISP1 and /31 from ISP2. All servers behined my router is using IPs from /28. I want that if one of the ISP failes,...

Getting error on Catalyst 9000 Always-On Sandbox -20251231T08221062

i'm getting this error when try to launch Catalyst 9000 Always-On Sandbox -20251231T08221062@Torque was not able to complete launching your environment.For more details, contact your space admin

CUCM Cluster Migration Plan – Z-Maxs to X-Maxs

Dear Seniors,need advice on best practices for a CUCM cluster migration. Below are the details of the existing environment and the services that must continue after the migration.There are two companies:1st Company: Z-MaxsPurchased 10,000 DIDs from a...

Can you do Main and Extended from laptop on dual screen EQ room?

Hello, I have an request to use the USB-C at the table to do main and extended on the 2 displays connected to the EQ. This is as in using the room as presentation only, not in a call.  Right now we are using the Atlona AT-OME-MS42 with great success ...

Work from Office Guided Resources

How to Adjust Voltage WS-CAC-4000W-US Power Supply

anyone know how to adjust the 42v DC level of a WS-CAC-4000W-US power supply  ? I assume it is found 'inside' the supply. Any idea how high I can get it  ?