Buy or Renew
Buy or Renew
Welcome to the Community!
The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally.
New Here? Click here to learn more and get started.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
2132908members
1463777discussions

Featured Content

Trending Topics

Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!

Community Activity

Start a conversation

IP 7900 Series, Displays turning off.

Hello All,We have some legacy 7900 colour IP phones on a cucm install, however the displays keep entering sleep mode, is there a way to turn them on 24/7 as they seem to turn off randomly.  current settings are for both common profile, enterprise pro...

IPFox by • Community Member
  • 207 Views
  • 2 replies
  • 0 Helpful votes

HWIC-16A Configuration - Hardware fault?

I'm trying to configure a HWIC-16A as a terminal server without success. I can get a telnet session to connect, but I simply get a blank screen, no data appears to be sent or received over the serial line.The only similar post I could find was https:...

802.1X auth fails certs missing CN

Hi FolksWe’ve recently started seeing a random issue on about 10 endpoints where both wireless and wired 802.1X authentication failsCurrent setup:Wireless: User + Machine authenticationWired: Machine authentication onlyAuthentication method: EAP-TLSC...

Incoming connections timeout or slow when do connect. isrc1111

i have had the system i have in place for some time and had no problems, when using a 2 router approach [isp1 and isp2] but since i merged both onto 1 device, ISRC111 there is an issue with incoming connections via isp1. i am using the same acl's and...

TheGoob by • VIP
  • 855 Views
  • 22 replies
  • 0 Helpful votes

VXLAN BGP EVPN Default Route

Hello all,  On Border Edges(DC01-BE001-6/7) am trying to advertise default route from GRT to MPBGP-EVPN but not able to do it properly with the following configruration. Thanks in advance for tips and correction **************************************...

uni1389_0-1766850713846.png
uni1389 by • Level 1
  • 226 Views
  • 7 replies
  • 0 Helpful votes

Cisco secure firewall 1200 series

I cannot find anywhere if the local admin account for FDM has a break class in any documentation. If say the account has been compromised. Can we console into the cli to reset the pw or do we have to reimage firepower and reload the configs?

pariemala82 by • Community Member
  • 189 Views
  • 4 replies
  • 0 Helpful votes

FMC Broken Database

Unfortunately, neither Cisco nor our partner is able to assign the contracts to us, so I can't create TACs. Therefore, here in the forum:We have a defective database in the FMC. Here's the error message:[Mon Oct 20 11:50:12 2025][FATAL] [missing all ...

Resolved! OSPFv3 Interface ID

Hello, everyone. I understand that OSPFv3 separates links from prefixes and purposely moves the prefix information from T1/T2 LSAs into T8/T9. The RFC states the following: o The Hello packet now contains no address information at all. Rather,...

Mitrixsen by • Level 1
  • 208 Views
  • 5 replies
  • 0 Helpful votes

Netconf Authentication Failure

Hello,I am working on a new deployment of Catalyst Center 2.3.7.10 and the new Catalyst 9350 switches. I have used PNP to onboard the switch to catalyst center, assigned hte switch to a site and then provisioned the device which pushed down the inten...

Switch Control Plane Traffic

I want to know about how a Switch forward it's control plane traffic like cdp/vtp/dtp messages on a trunk. Will they be forwarded with tag or untagged and why??

Load more